proSilence PCS-350 Fanless PSU

Power
Viewing page 3 of 4 pages. Previous 1 2 3 4 Next

TEST METHODOLOGY

Parameters Tools
DC load on PSU DBS-2100 PSU load tester
Ambient temperature
Any number of thermometers
DC voltage regulation
Heath / Zenith SM-2320 multimeter
AC power
Kill-A-Watt Power Meter

The core PSU test tool on SilentPCReview's test bench is the DBS-2100 load tester, made (in Taiwan by D-RAM Computer Company) specifically for testing computer power supplies. The machine consists of a large bank of high power precision resistors along with an extensive selection of switches on the front panel calibrated in Amps (current) and grouped into the 5 voltage lines: +5, +12, -12V, +3.3, -5, +5SR. Leads from the PSU connect into the front panel. It is shown above with leads from a PSU plugged in.

The DC output connector closest to the PSU on each set of leads is hooked up to the load tester. This ensures that the current delivered is distributed to as many short leads as possible. The heat generated in the wires can be an issue when pushing a PSU to its rated output,

The proSilence was tested at 4 DC output power levels:

  1. 65W: A very typical DC power draw by many system at low / modest load.
  2. 90W: Established previously as a typical max power draw of a midrange desktop PC.
  3. 150W: For higher power machines.
  4. 170W: The maximum

Care was taken to ensure that the load on each of the voltage lines does not exceed the ratings for the PSU. The PSU is left running 5~10 minutes at each power level before measurements are recorded.

The DBS-2100 is equipped with 4 exhaust fans on the back panel. A bypass switch toggles the fans on / off so that noise measurements can be made. The resistors get very hot under high loads.

Kill-A-Watt AC Power Meter is plugged into an AC outlet on the side of the DBS-2100 in the above picture. The AC power draw of the PSU is measured at each of the 4 power loads. The Kill-A-Watt is used to measure:

Efficiency (in AC-to-DC conversion) at each power level. This is the efficiency figure provided by PSU makers. It is obtained by dividing the DC power output (as set on DBS-2100 load) by the AC power consumption. Efficiency varies with load, and also temperature. PSUs seem to run more efficiently when warmer, up to a point. Generally, they are least efficient at low power and most efficient at 40~80% power load. The main advantage of high efficiency is that less power is wasted as heat -- this means a cooler PSU that requires less airflow to maintain safe operating temps (read: quieter.)

Power Factor (PF). This measurement can be read directly off the Kill-A-Watt. In simple terms, it tell us how much AC power is lost to harmonics (unnecessary electromagnetic energy) while driving the PSU. In practical technical terms, it is the difference between the measured V(oltage) x A(mperes) and AC power in Watts.

PF varies somewhat depending on load. The ideal PF is 1.0, which means no AC power is lost. A PF of 0.5 means that to deliver 100W in AC to a PSU, your electric company actually uses 200W and this is often shown in your electric bill as savings (depends on your electric utility company and your account with them). 100W is lost or wasted. Active PF Correction (PFC) power supplies usually have a PF of >0.95. Passive PFC units usually run 0.6 - 0.8. Non-PFC units usually measure 0.5-0.7. PF is not significant in terms of noise, heat or performance for a PC, but it is relevant to electricity consumption and energy conservation.

The Heath / Zenith SM-2320 digital display multimeter, a fairly standard unit, is used to measure the fan voltages and the line voltages of the PSU output. The latter is done via the terminal pin on the front panel, above the connections for the DC outputs from the PSU.

The Test Lab is a spare kitchen measuring 12 by 10 feet, with an 8 foot ceiling and vinyl tile floors. The acoustics are very lively and allows even very soft noises to be heard easily. The PSU under test is placed on a piece of soft foam to prevent transfer of vibrations to the table top. Temperature in the lab is usually ~20C. This is something of a problem as PSUs usually operate in environments that easily reach 45C. Sited next to or above the CPU, the PSU is always subject to external heat. This brings us to the next topic...

In-case Thermal Simulation

The solution is a AC bulb in an empty case with the PSU mounted normally. The distance between the bottom of the PSU and the top of the bulb is about 7 inches. With the proSilence, a 60W bulb was used for all the load tests. It seems unlikely that this PSU would be used in a system that generates gobs of power and heat. The bottom front vent of the case and its bezel have been modified for unrestricted airflow; the approximate size of the intake hole is the equivalent area of a 92mm fan,

The PSU must cope with the heat generated by the light bulb plus whatever heat it generates within itself. In a real system, there would be other air exhausts paths and mostly likely at least one case fan. So a Panaflo 80mm L fan was mounted on the back panel of the test case and connected to a voltage controller. The PSU was run through its load range with the fan turned on to 7V, about the level at which most PC silencers would run their case fan.

Noise Measurements - For once, none were needed!



Previous 1 2 3 4 Next

Power - Article Index
Help support this site, buy from one of our affiliate retailers!
Search: