The Skyscraper Photo PC
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
The Skyscraper Photo PC
Here's my latest silent PC creation. It is a hybrid PC/digi-frame that I designed to sit on a mantle or similar "silence-required" area. It can also sit on desk and act as a basic e-mailer/web surfer.
It has a fanless VIA CN10000 board and a 2GB compact flash card plugged into a CF/IDE adapter.
The only noise comes from a 60mm Vantec Stealth fan. I had to include the fan...well....just in case. The fan is routed through one of those Powermate fan controllers and I have it turned down all the way.
I haven't tested it yet without the fan running but that is coming soon.
So what do you think?
http://slipperyskip.com/page22.html
It has a fanless VIA CN10000 board and a 2GB compact flash card plugged into a CF/IDE adapter.
The only noise comes from a 60mm Vantec Stealth fan. I had to include the fan...well....just in case. The fan is routed through one of those Powermate fan controllers and I have it turned down all the way.
I haven't tested it yet without the fan running but that is coming soon.
So what do you think?
http://slipperyskip.com/page22.html
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
Thanks for your feedback. The Vantec is barely turning and the system is staying cool. I'll probably disable it completely after a little more testing.thejamppa wrote:That is awesome! Its like piece of decoration. You can easily place that for aesthic pleasing and most won't even know its a computer.
You could however try see if you can fit 60 mm -> 80 mm adapter and hook Nexus 80mm. It would be much quieter than Vantec Stealth.
You're an artist with a real eye for detail (that light pine/beach veneer trim sets it off perfectly )
Are the chrome 'switches' operational? (if not, have you seen these qprx touch sensor ics? http://www.qprox.com/products/qtouch.php )
Are the chrome 'switches' operational? (if not, have you seen these qprx touch sensor ics? http://www.qprox.com/products/qtouch.php )
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
Thanks Bill!BillTodd wrote:You're an artist with a real eye for detail (that light pine/beach veneer trim sets it off perfectly )
Are the chrome 'switches' operational? (if not, have you seen these qprx touch sensor ics? http://www.qprox.com/products/qtouch.php )
I decided early in the project that front-mounted video screen controls weren't going to happen. The only controls are brightness, contrast, blah, blah and I hardly ever fool with that stuff once it is set.
Instead, I mounted the control PCB inside the casing. Four thumb screws on the back panel gives me access to these controls. It was a cost/benefit decision. Controls made for thin skinned enclosures just don't play well with much thicker wood walls.
Towards the end of the project I realized that I needed something shiny on the front. I'm not a big fan of fake things but in this case I got my shiny without it looking out of place.
That link you provided looks very interesting. Thanks for that.
The light-colored accents are actually a lighter grade of mahogany that haven't been so highly finished. They will get darker with time but so will the rest of the case.
-
- *Lifetime Patron*
- Posts: 5316
- Joined: Sat Jan 18, 2003 2:19 pm
- Location: St Louis (county) Missouri USA
Man.....what a project for a digital picture-frame. I think I would have saved time/trouble by making the thing out of solid wood sections, combining different wood types......rather than veneer the project. Cutting all those little pieces would have driven me crazy. And I like the idea of a sunshine drying/aging process. The thought of warped panels in such a project is cause for concern with wood.
Nice computer however.....at great cost of time.
Nice computer however.....at great cost of time.
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
-
- Posts: 3142
- Joined: Mon Feb 26, 2007 9:20 am
- Location: Missing in Finnish wilderness, howling to moon with wolf brethren and walking with brother bears
- Contact:
It looks like old radio or something... Its truely piece of an art. When you do next project, you could use potento meter to adjust fan. And hide the potento meter inside wooden turn knob. That is way you could control it easily. I am not sure does VIA make ITX boards that have PMW's they could good solution too.
But I just love the wood.
But I just love the wood.
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
-
- *Lifetime Patron*
- Posts: 5316
- Joined: Sat Jan 18, 2003 2:19 pm
- Location: St Louis (county) Missouri USA
slipperyskip......I know it's too late now, but here's what I would have done with that fan. Some airflow through the case is probably necessary, but not much. I would have eliminated the rear fan, and placed a quiet 60/80 mm fan under the heatsink area blowing upward. I would have routed out that top wood section so that an opening faced the rear. Convection currents would pull cool air in the bottom openings, and would be helped by the single fan. The exhaust would passively leave the upper vent slot....., probably quieter.
You could attach the fan to a NoiseMagic NTM3 auto-controller if you thought you might need more airflow on hot days. I don't think many/any VIA boards have fan speed controls. Just a thought....
You could attach the fan to a NoiseMagic NTM3 auto-controller if you thought you might need more airflow on hot days. I don't think many/any VIA boards have fan speed controls. Just a thought....
what I love about all of SS's designs is they have a strong Art Deco/Retro feel about them...like a 30's/40's throwback to when guys wore spats and jackets with wide lapels.
SS, have you thought of doing a computer that is fully integrated into a wooden desk? this would take the theme of hiding computers "in plain sight" to the next level....
great work, as usual
SS, have you thought of doing a computer that is fully integrated into a wooden desk? this would take the theme of hiding computers "in plain sight" to the next level....
great work, as usual
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
Good ideas but...where would you put an 80mm fan?Bluefront wrote:slipperyskip......I know it's too late now, but here's what I would have done with that fan. Some airflow through the case is probably necessary, but not much. I would have eliminated the rear fan, and placed a quiet 60/80 mm fan under the heatsink area blowing upward. I would have routed out that top wood section so that an opening faced the rear. Convection currents would pull cool air in the bottom openings, and would be helped by the single fan. The exhaust would passively leave the upper vent slot....., probably quieter.
You could attach the fan to a NoiseMagic NTM3 auto-controller if you thought you might need more airflow on hot days. I don't think many/any VIA boards have fan speed controls. Just a thought....
I pack'em solid.
I've been running the system fanless for the last hour with a full photo slideshow (w/ transitions). Natural circulation seems to be working fine for my application.
Shouldn't be surprised. The VIA CN package is rated at 9.3W at idle which is what it is doing running a screensaver slideshow. The CF card doesn't generate heat. The picoPSU is very efficient.
The only unknown was the LCD panel. It appears to be a power miser also.
-
- Posts: 436
- Joined: Fri Feb 17, 2006 8:15 pm
- Location: Michigan
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
Thanks jaganath! I respect your opinion. No old desks will harmed by my obsessions. That's where I draw the line.
I tried doing a notebook to digi-frame conversion but was stumped by the keyboard. I thought I could disconnect the internal keyboard and use the external keyboard port instead but that was a bad assumption.
Maybe it was the model I was working with. Be wary.
Caffeine Free Diet Coke....the power drink for old farts.Chris Chan wrote:I love it. I'm thinking of doing something similar to the guts of a 12" iBook. Only thing is, why use a can of *caffeine free* Diet Coke as a size comparator? I need my caffeine!
I tried doing a notebook to digi-frame conversion but was stumped by the keyboard. I thought I could disconnect the internal keyboard and use the external keyboard port instead but that was a bad assumption.
Maybe it was the model I was working with. Be wary.
-
- Posts: 436
- Joined: Fri Feb 17, 2006 8:15 pm
- Location: Michigan
Ehh, I'm not an old fart. I'm only fifteen.slipperyskip wrote: Caffeine Free Diet Coke....the power drink for old farts.
I tried doing a notebook to digi-frame conversion but was stumped by the keyboard. I thought I could disconnect the internal keyboard and use the external keyboard port instead but that was a bad assumption.
Maybe it was the model I was working with. Be wary.
It may well have been an iBook; mine doesn't boot without the keyboard connected. I might just leave it there internally as it's maybe 5mm thick.
-
- *Lifetime Patron*
- Posts: 5316
- Joined: Sat Jan 18, 2003 2:19 pm
- Location: St Louis (county) Missouri USA
slipperyskip......I'd get a 15x80mm San-Ace fan from Sidewinder Computers (that's the best/quietest you can get). Then I'd turn it into a slot-fan by cutting the end of the fan frame. Link to slot-fan mod I'd mount it right over the CPU area of the heatsink, sucking off the heatsink, blowing over the top of the ram sticks, toward the top of the case. You'd only need another 18mm or so between the back of the monitor, and the top of the heatsink to do this mod.
You'd cool the cpu heatsink better, and you'd have some airflow over the back of the monitor.
You'd cool the cpu heatsink better, and you'd have some airflow over the back of the monitor.
-
- Posts: 312
- Joined: Tue Jul 24, 2007 3:57 pm
- Location: Minnesota
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
-
- Posts: 312
- Joined: Tue Jul 24, 2007 3:57 pm
- Location: Minnesota
rofl! nicely done. I have a mini shuttle case that I want to mod out a bit to build a epia file server.
I'm thinking why run my main rig [200W+] 24/7 when I just just need apache server/ftp server/storage. It doesn't need to be as pretty as yours, but I need a hard drive cage bay with good ventilation, something to attach the motherboard/power supply too, and some way to hold it all together.
I'm thinking why run my main rig [200W+] 24/7 when I just just need apache server/ftp server/storage. It doesn't need to be as pretty as yours, but I need a hard drive cage bay with good ventilation, something to attach the motherboard/power supply too, and some way to hold it all together.
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
People have been stuffing mini-ITX boards into almost anything for years. You should check out the projects at mini-ITX.com for some inspiration.
There I think you will find all kinds of different ways to mount boards and peripherals into almost any enclosure.
The Skyscraper Photo PC made Gizmodo and Boing Boing yesterday. My favorite though was Cowcotland...a huge French gadget site. Something oddly satisfying about reading about your work in a foreign language. lol
Cowcotland
A comment at Gizmodo motivated me to post a size comparison photo. Sometimes you get so close to a project you lose perspective...literally.
There I think you will find all kinds of different ways to mount boards and peripherals into almost any enclosure.
The Skyscraper Photo PC made Gizmodo and Boing Boing yesterday. My favorite though was Cowcotland...a huge French gadget site. Something oddly satisfying about reading about your work in a foreign language. lol
Cowcotland
A comment at Gizmodo motivated me to post a size comparison photo. Sometimes you get so close to a project you lose perspective...literally.
-
- Posts: 436
- Joined: Fri Feb 17, 2006 8:15 pm
- Location: Michigan
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
Slipperyskip is the name of the road I live on.Chris Chan wrote:Another diet soda, huh? And you're famous for getting written up in French. What's with the "SlipperYskip" thing though?
I'm famous for other things too. lol
http://slipperyskip.com/page15.html
-
- Posts: 436
- Joined: Fri Feb 17, 2006 8:15 pm
- Location: Michigan
-
- Posts: 140
- Joined: Thu Aug 14, 2003 6:52 am
- Location: Florida
- Contact:
slipperyskip wrote:Yes.....you could also see how I built it on my website. ; )Blacktree wrote:Hey Slipperyskip, that's pretty cool. Can you show us a photo of the backside?
http://slipperyskip.com/hammond/058.jpg