OK - gotta ask: where on earth did you get that heatsink that sits outside of the chassis? Did you build it yourself or from a kit? I certainly haven't seen anything like that from Thermalright.

And I thought I was a Thermalright whore since my desktop has an HR-03 GT, an HR-05 IFX SLI and an XP-90 in it...I'm awestruck.

-D

It's DFI Transpiper. I haven't bothered installing mine as it doesn't do much.

Ah. Thanks for the info, Kepakko.

Actually, it reminds me of some sort of grilling device - but I doubt it gets that hot.

-D

Is that heatsink behind the rear fan an hr05? What is it connected to?
Got lots of aluminium in there

OK. One more stupid question: where is the fresh air coming from to the HDD chamber and the PSU chamber? I don't see any intakes, which can't be good for the components (unless it is coming from below, in which case there doesn't appear to be much clearance underneath the chassis).

-D

PSU fan is pulling it in from the front.

IKIKUINTHENUTZ can you tell us more about your rig?

What do you get when you cross Snoop Dogg, a computer geek, lots of thermal paste,and a fat wallet?...Pimpin.. . ....But seriously, that's impressive. How much does it weigh? And I'm a bit curious on the performance of the hr-03+, since other than that one German site (sorry I forgot the name of it), there doesn't seem to be many thorough reviews on the heatsink.

nice bling bling effect, but what are specs of system, and temps of all components?

I don't think you have enough heatsinks.

thats crazy.

well done

looks like a good wtx case too...

I looks like it has the makings of a quiet pc, lots of passive heatpipes and whatnot, but can it be true with still having that many fans?

Unlikely, but quiet is in the eye of the beholder.

Wow you can hear with your eyes!



It looks like the HS on back blocks two of the monitor ports?....

how much did all those heatsinks cost?

Look at the 5th photo - he's using Crossfire - no need for multiple monitor ports.

-D

so shiny!! my preciousssss...

Just more picture with details


Amazing Enough, A HR-09 Type 3 perfectly fits onto HD3870s with push pins

Side panel FOamed up

as you can see, foam is wedged between the pexi and side

Every section you see with foam comprosed of 3 layers
1. Silicone adhesive which very easy to remove
2. Neoprene sheets for adding mass and make easy clean up if I remove the foam
3. Either I use Sonex Acoustic (melamine foam, white) or Some inexpensive cellous foam (sponge, commonly found in black) you can get from any computer shop

Finnaly after weeks of searching this rare long crossfire cable, asus includes them in their High end AM2+ motherboards and I was able to get this rare cable off of ebay

the other side panel

"Lord Vader, your computer is ready."

(Anyone remember those Impala ads from circa 1995?)

Both cards in Crossfire, results recorded using ATi Catalyst in OverdriveTM sub menu, MX-2 were used as the TIM during the mounting of the aftermarket HR-03 coolers

Both card's clock speeds are
Core: 800
mem: 1170
HD 3870s

#1 is the bottom card
#2 is the top card next to 2 fans

Ambient 22c
Idel
#1: 43c
#2: 36c

Load
Results Recorded during the 30 mins of crysis game play by average
#1: 71
#2: 51

Im trying to replace the side panel for one with side exaust to furthur reduce tempatures

Other info
DFI X38
Q6600
PCpower cooling 750w silencer
2 X 250 GB single platter seagates in raid 0/1 intel matrix

IKIKUINTHENUTZ Very nice built you have there.
I was more interested in the damping you used.
Did it have any effect in reducing the noise produced,how you describe the noise before and after foam was applied?(I mean all this layers)
Congrats again on the built.!!

Hello,

The fan grills seem to be pretty restrictive. I think that it takes the cake on heatsink surface area...

Without damping, the case made a somewhat hollow echo noise. This case is huge and I barely have anything inside of it XD

I am going to increase the damping and add in a side fan when I get my brand new sidepanel, no ugly pexiglass for me.



Already working on it mate I left it in because it looks asthetically good to me, im working on a plain fan grill spray painted black lol

You're still missing one HR-11
Nice, hefty build, lotsa metal & cooling surface.
I'm always wondering - how quiet those PC P&C beauts are?

I already tried, it is impossible to add another HR-11 on the 2nd card due to space constraints

Honestly im suprised how quite my PC P&C is with a 80mm san ace inside of it. I guess it's seasonic's ingenuity trademark in all their psus (it's a seasonic OEM) but I have heard cosair psu noise levels and they are a bit lower in fan motor noise.

I got my new side panel recently and some SLipstream fans, I will post updated pics later

You can use HR 05 SLI instead of HR 05 and you'll have more space near the 2nd VGA card...

Where did you get the material from.
Thanks

Again another question about dampening.
Which product exactly from Sonex did you use?
I mean there are a bunch products in Sonex wed site,did you use the classic foam or Sonex One Foam?
Thanks,and again congrats for your built.

There is no HR-05, it is clearly shown in all my pictures, if your thinking of over lapping over to the DFI NB heatsink then that is still impossible, the HR-03 on the first card blocks the only other possible orientation of a HR-11 on the 2nd card, the other 2 ways are still blocked by the first card PCB



Jab-tech, SVC, Performance-pcs, Xoxide.com, MPtech, Ace Hardware, and my personal favorite http://www.mcmaster.com/

Sonex Mini 1"