Page 1 of 2
Revamped: The Elysium Beast V2.8, 23 HDDs and 18.0 TB
Posted: Thu Apr 05, 2012 7:40 am
by pm.stacker
Updated V2.8
These days I'm stocking up on some new components to build my "version 2.0" Xeon workstation, this time big nasty and quiet
for the previous build from 2009, see "The quiet beast Xeon workstation" topic
V2.8 config 8/8/2013
Case Xigmatek Elysium
silver without window (DIY made)
CPU Intel Xeon E5520 x2
Board Tyan S7025AGM2NR
RAM Corsair Registered ECC DDR3-1333 (16384MB)
PSU Enermax Platimax EPM1000 (1000W Platimax)
Graphics Nvidia Quadro 4000 Supercooled DIY Edition
Storage controllers Promise Supertrak EX16650+EX8650 (total 24 ports), onboard ICH10R, Marvell 88SE9128
Audio Creative Sound Blaster Audigy2-ZS Platinum Pro, Realtek ALC262
SSD OCZ RevodriveX2 RVDX2-100G
Firewire800 LSI 2+1 port X1 card
HDD 6xWD10EADS, 2xWD10EACS, 4xWD1003FBYX, 4xWD5003ABYX, 2xWD5000BEVT, 2xWD5000BPVT, 2xHTS547564A9E384, 1xWD2500HHTZ
Optical Drive Optiarc BD-RW BD-5730S
Optical Drive Optiarc BD-RW BD-5740H
Optical Drive MATSH|TA DVD-RAM SW-9576S (UDMA-4)
Optical Drive HL-DT-ST BD-RE GGW-H20L
Optical Drive HL-DT-ST BD-RE GGW-H20L
Optical Drive HL-DT-ST BD-ROM GGC-H20L
CPU cooling 2x Noctua NH-D14SE2011 (adapted to Xeon mount) with 2x NF-P12-PWM
Exhaust Nidec Servo Gentle Typhoon D1225C12B4AP-14 (1450RPM)
Chipset cooling 2x Thermalright HR-05 IFX (DIY bracket)
Cards cooling Corsair Air Series SP120 Quiet Edition (1350RPM)
HDD cooling 2x Scythe Slip Stream Slimline SY1212SL12SL
Building should start next week...
Re: The quiet beast V2.0: Xigmatek Elysium!
Posted: Fri Apr 06, 2012 12:21 am
by cordis
Hey, looks like a good case. I have a dual opteron 6174 system in a cosmos 1000 case, in that one I put the dual fans up top, turned both heat sinks up, and switched the rear output fan around so that it blows into the case. That seems to keep the chips fairly cool, I think they run around 50s-60sC at full load. For my dual xeon system, I have a stack of fans pushing the air, keeps them pretty cool.
Re: The quiet beast V2.0: Xigmatek Elysium!
Posted: Fri Apr 06, 2012 12:51 am
by pm.stacker
I would do the same but I have to place the PSU in the upper position (I had some trouble finding a new big case which allows for good old top PSU placement, the other would've been Lian-li PC-A70B but it has only 7 internal fixed HDD slots and I need 8+2... with Elysium I recycle my old SAS backplanes
), so your setup is fine with PSU on bottom but in that position it'd blow towards the table (<1" clearance) and I'd have to reposition power cable. Courier van is on its way with it, let's see...
Other HSF alternatives would be: 2x Thermalright HR-02-Macho or the new Noctua NH-L12, might even try my good old NH-U12DX
Re: The quiet beast V2.0: Xigmatek Elysium!
Posted: Fri Apr 06, 2012 11:30 am
by pm.stacker
This morning the beast arrived
Just finished emptying it from everything that was stock mounted (HDD cages, fans, ties, slot covers, filters, cable rubbers...)
I'm writing the TODO list for this new build
this time I want it done nicely and perfectly
1) replacing, when possible and useful (i.e. mobo tray), the standard riveted junctions with M3 or M4 double-bolted junctions
2) replacing stock wheels with industrial-duty ones (rated 45kg each)
3) tidying up roof connections block to make bay#1 usable with standard 5.25 devices
Will have to study some strengthening method for PSU up there, not that Enermax Platimax weighs a ton but I'd like something sturdier. Then, prepare side exhaust (the 5 tubing holes) and Lian-li slot cooler for cards side placement. I am already thinking about a fully ducted cooling system for everything, from HDD cages to CPUs, hey exhaust grilles are there for something...
planning on getting some PVC tubing, Ø80 or Ø100, if I can make something good pipes will be painted satin-black
(or maybe shiny silver?
)
Re: The quiet beast V2.0: Xigmatek Elysium!
Posted: Sat Apr 07, 2012 9:42 am
by pm.stacker
4) replace the original crappy lame power-reset buttons with something better
Re: The quiet beast V2.0: Xigmatek Elysium!
Posted: Sun Apr 08, 2012 2:40 am
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium!
Posted: Mon Apr 09, 2012 1:57 am
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Thu Apr 12, 2012 2:09 am
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Thu Apr 12, 2012 3:56 am
by KadazanPL
The question is how much vibration damping will this HDD cage give you. And the answer is... none.
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Thu Apr 12, 2012 4:11 am
by pm.stacker
I have my HDDs in server SAS backplanes since 2009, without any kind of vibration dampening. And they vibrate very little. And keeping frame extremely rigid vibrations are absorbed by the whole case (tested this on my Stacker: an old 7200 HDD vibrated more with a medium-class suspension than bolted to the case!
) of course total suspension with elastic cords yelds the best results (at expense of hot swapping, with some bicycle inner tube it could even be done on these Lian-li cages) but i'm not planning on the dead silent system, just a quiet one (remember, 2x Xeon with 32GB...). A good compromise between quietness, structural strength and power
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Thu Apr 12, 2012 4:39 am
by pm.stacker
Auxiliary support bar for very heavy heatsinks (i.e. Noctua U12 or TR HR02)
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Thu Apr 12, 2012 2:33 pm
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Sat Apr 21, 2012 1:44 am
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Fri Apr 27, 2012 2:30 am
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Tue May 01, 2012 4:19 pm
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Wed May 02, 2012 6:19 pm
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Sat May 05, 2012 10:30 am
by pm.stacker
Solved the relay issue with a 10 times longer RC time constant on the 4013 reset network.
Today the big works start
I started dismantling the old Stacker-based workstation to transfer the components that will be recycled
Placing the VM SSD in between the two slimline ODDs
Time to open this box...
HDD compartment almost filled. Cable simulation with the new 16650 card.
Optical drives condo...
Laying new and old cards on the floor. The hefty and powerful Quadro 4000 always stands out...
A mod I wanted to do but never tried: mounting silent fanless heatsinks on the two i5520 northbridges. As you can see, two Thermalright HR-05 placed side by side are a perfect fit
but now I have to build some modified retention brackets, since Tyan placed the HS holes on the mobo waaaayyy distant one from the other and the ones Thermalright includes are too short
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Mon May 07, 2012 2:36 am
by pm.stacker
First build tests, Enermax UCCL12
Hybrid mobo fixing system: UNC6/32 raised stock standoffs towards the rear (since I can't remove the rear plate), M4x20 bolts and steel+nylon washers for other points, best strength and self-centering (std mobo holes are Ø4). Height adjustment to make cards fit (with stock standoffs mobo was a lil' too low).
Testing side cooler placement. Unfortunately fan grilles touch the full-height expansion cards, that would be a non issue if it wasn't for the Audigy2 which has the power connector protruding on that side
so: 1) remove grilles and secure cables to prevent getting into the fans 2) mount two Scythe Slip Stream Slimline fans (SY1212SL12SL 800RPM) 3) swap the Audigy2 for an Asus Xonar D1 low-profile.
Testing the new lighting system
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Mon May 07, 2012 11:05 am
by pm.stacker
Today first test power up. For anyone wondering about vibration damping of my DIY 3x4xSATA compartment, tried it with my old 8 HDDs and two Hitachi 2.5": almost NO vibration, even slightly better than with the Chieftec backplanes, and very low vibrations trasmitted to the case. It seems that 11 fixing points and square-sized hollow bars do their job...
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Mon May 07, 2012 3:57 pm
by Blood
Holy, what a beast. Love the build.
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Mon May 07, 2012 4:05 pm
by Blood
KadazanPL wrote:The question is how much vibration damping will this HDD cage give you. And the answer is... none.
Not sure how you would go about dampening vibration for 12HDDs. Is soft mount still the best option at the point? How does the vibration of 12 HDD spinning at the same time affect each other (resonance) ?
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Mon May 07, 2012 4:11 pm
by Blood
Thinking more about it. AT the point, the sheer weight and regidity of the casing might matter more. My ancient Antec P180 vibrates despite the suspension with 4 Seagate 3TB hard drives.
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Tue May 08, 2012 1:45 am
by pm.stacker
Of course it depends on which HDD models you have. My WD RE4 drives (4xWD5003ABYX) are 7200 and enterprise but they seem to have only 1 platter and a good spindle motor that produces little vibrations and resonance. Old WD10EADS drives were always good at vibration (EARS are even better but they're mad slow
). And for now the +2 HDDs are two Hitachi HTS547564A9E384, some of the quieter 2.5"s I have.
Maybe even horizontal mounting plays a little part in this (my former Chieftec caddies were vertical). All modern HDDs should be mountable in every position but I still think that the motor bearings are designed to work best horizontally, especially nowadays with bolt-thru-spindle drives a rarity.
And remember, the "stock" Elysium is more cheaply built than the glorious Stacker: it uses slightly thinner steel and dosen't have the removable mobo tray. On the Stacker it was removable and it could be flipped for BTX but it had a hefty 6mm welded steel support frame and the tray itself was shaped to maximize torsional rigidity. With full bolting and some reinforcements I somehow managed to get a better Elysium
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Tue May 08, 2012 12:33 pm
by pm.stacker
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Tue May 08, 2012 6:58 pm
by pm.stacker
With a slight modification to the rear reinforcement bar...
I can accomodate a dual Esata and power bracket in the 8th slot
ATA133 cable placement
And after some hours and a lot of cable ties...
almost completed cabling, remains to do front USB, Audio and Esata+Dock
Rear connections
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Wed May 09, 2012 4:00 pm
by pm.stacker
First power up with everything cabled inside:
good silencing to start with, but I'm running it without side panel to check everything's alright.
Tested the top HDD dock: my little pushbutton circuit makes it amazing
just place a HDD in, then press the red button front
all 2+1 Esata ports and Dock are connected to the Marvell 88SE6145 which supports hot-plugging:
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Wed Jun 13, 2012 3:38 pm
by pm.stacker
Testing a "quiet" Quadro 4000 card.
not fanless silent, but with the Spitfire GPU stays at 40°C on exhaust fan, stock fan stays silent at 2000RPM, quite a difference from 76°C and 4500RPM fan.
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Sun Jun 17, 2012 2:22 am
by neumein
This build creates a stir in my loins.
Some serious HDD-porn in there
Re: The Quiet Beast V2.0: Xigmatek Elysium and 12+ HDDs
Posted: Thu Dec 20, 2012 10:07 pm
by Horgrim
Re-upload the pictures please!
Re: Revamped: The Elysium Beast V2.4, 20+ HDDs
Posted: Sat Jan 12, 2013 6:47 am
by pm.stacker
I had changed URL to make them invisible out of another forum in which this build was in a competition that now ended and I forgot to re-enable them
now I have to do some lil' repair work at my aunt's house, tonight the last mods pics