Silent home server with InterTech SY-608 and 4 HDDs build
Posted: Wed Jul 31, 2013 1:27 pm
Hey dudes, I managed to put my home server system together today. Here is the story.
The previous server had a cheap MoBo, an intel celeron dual-core 2GHz CPU, 4GB RAM, and 4x1TB HDD's using software RAID5. Running Debian 7.
I decided to upgrade the CPU to a six-core AMD 6300 FX, and had to get a new MoBo as well. The new MoBo was bigger than the old one, and didn't fit in the old case. So I had to use the desktop's case to fit the server into it while I figured out what new case to get. The desktop machine then ran without a case for a while.
The discussion for choosing the case is in here.
I chose this case because it has all 5" bays, so I could easily suspend the HDDs using elastics. In the end I used more than 4 meters of elastic just to hold 4 HDDs.
Before looking at the pictures below, you might want to check the pictures on their website.
Sorry about the quality, all I had available was a phone.
The way it was setup before the build:
HDDs were mounted with screws:
Added elastics to new case:
Elastics from the back. Later I figured I should have tied the bow at the back and got a cleaner look at the front, but it's not really important, seeing as the case remains closed.
I started by putting the HDDs in from the top, but this was a mistake, since it's a lot easier to start from the bottom:
Adding Motherboard:
Adding Seasonic power supply:
The PSU filter below the case is semi-removable:
Changing the CPU cooler:
The stock AMD cooler left a strange pattern on the CPU itself:
After wiping the thermal paste off, dust around it with a paint brush.
Adding in the Arctic Cooling Freezer 7. I had no choice but to mount it blowing upwards, since I couldn't turn it 90°.
I later removed the case fan visible on the left:
Cable management:
Here is the 12V CPU cable:
Bundling up the unused cables:
Adding SATA cables:
Adding front panel cables:
Running in the corner:
Now for the desktop computer, moving it into the white case you saw in the first picture:
Also mounted its ATA HDD with elastics:
When first plugging in the power, I did not realize it had turned on, I had to see the front LED to get it. But after a few seconds it started making fan noise, one of the fans started turning faster. The Freezer 7 seems to run at a higher RPM. When booting up, it is silent, but after a while it starts to spin faster and make audible noise.
I noticed that it generates a lot of heat. I put my hands on the HDDs and they were hot just after a few minutes, so I moved the small fan you saw in the pictures above in front of the HDDs. It doesn't have a lot of intake space, so it doesn't really do an efficient job.
I'm thinking of getting another fan, as well as a case fan to help it, and a better HDD fan, maybe a couple of 140mm fans.
Overall I'm pleased with it.
What do you guys think?
The previous server had a cheap MoBo, an intel celeron dual-core 2GHz CPU, 4GB RAM, and 4x1TB HDD's using software RAID5. Running Debian 7.
I decided to upgrade the CPU to a six-core AMD 6300 FX, and had to get a new MoBo as well. The new MoBo was bigger than the old one, and didn't fit in the old case. So I had to use the desktop's case to fit the server into it while I figured out what new case to get. The desktop machine then ran without a case for a while.
The discussion for choosing the case is in here.
I chose this case because it has all 5" bays, so I could easily suspend the HDDs using elastics. In the end I used more than 4 meters of elastic just to hold 4 HDDs.
Before looking at the pictures below, you might want to check the pictures on their website.
Sorry about the quality, all I had available was a phone.
The way it was setup before the build:
HDDs were mounted with screws:
Added elastics to new case:
Elastics from the back. Later I figured I should have tied the bow at the back and got a cleaner look at the front, but it's not really important, seeing as the case remains closed.
I started by putting the HDDs in from the top, but this was a mistake, since it's a lot easier to start from the bottom:
Adding Motherboard:
Adding Seasonic power supply:
The PSU filter below the case is semi-removable:
Changing the CPU cooler:
The stock AMD cooler left a strange pattern on the CPU itself:
After wiping the thermal paste off, dust around it with a paint brush.
Adding in the Arctic Cooling Freezer 7. I had no choice but to mount it blowing upwards, since I couldn't turn it 90°.
I later removed the case fan visible on the left:
Cable management:
Here is the 12V CPU cable:
Bundling up the unused cables:
Adding SATA cables:
Adding front panel cables:
Running in the corner:
Now for the desktop computer, moving it into the white case you saw in the first picture:
Also mounted its ATA HDD with elastics:
When first plugging in the power, I did not realize it had turned on, I had to see the front LED to get it. But after a few seconds it started making fan noise, one of the fans started turning faster. The Freezer 7 seems to run at a higher RPM. When booting up, it is silent, but after a while it starts to spin faster and make audible noise.
I noticed that it generates a lot of heat. I put my hands on the HDDs and they were hot just after a few minutes, so I moved the small fan you saw in the pictures above in front of the HDDs. It doesn't have a lot of intake space, so it doesn't really do an efficient job.
I'm thinking of getting another fan, as well as a case fan to help it, and a better HDD fan, maybe a couple of 140mm fans.
Overall I'm pleased with it.
What do you guys think?