It is currently Thu Jul 19, 2018 7:13 am

All times are UTC - 8 hours

Post new topic Reply to topic  [ 2 posts ] 
Author Message
 Post subject: My expiriences with Gigabyte Radeon9000 & Zalman HP80-C
PostPosted: Mon Nov 24, 2003 1:36 am 
Friend of SPCR

Joined: Wed Nov 12, 2003 4:52 am
Posts: 36
Well for anyone wondering if the mounting holes on the (gigabyte, don't know about others) radeon9000 cards would host the Zalman HP80-C well, the answer is 'sortof'.

I checked the zalman website for the requirements, and it said I needed mountingholes on my card. I checked out my radeon9000 card, found two mounting holes, and ordered the cooler.

It turns out however that the mounting holes aren't in the spots that the zalman would like them to be. If you look at the car with the connectors to the left, and the agp interface at the bottom, the holes are too close to eachother vertically.

You can get the heatsink to mount however, but you need to apply it slightly tilted in order for the screws of the heatsink to line up with the mounting holes. Since this is a bit of a tight fit, the screws have a tendency to not go straight in the holes, but at an angle, which gives a bit of trouble on the backside, since you need to mount another heatsink at the back. After a bit of tweaking though I managed to get both of them installed, albeit slightly tilted.

When I had to connect the heatpipe from the front to the backsink, I had the idea that I had to bend it slightly. It was such a small amount however that it didn't frighten me at all. I'm suspecting this to be the case in a normal scenario too, since the front and back heatsinks did line up properly.

All in all it's installed, and doesn't get hot at all (just feeling with my hand). I'd say defenitely under 30 degrees (20 degrees room temprature (celcius))

Would I advice is to anyone? It depends on your upgrade plans I assume. The radeon9000 doesn't need such a good cooling solution, I think it could have been passivly cooled in the first place. So if you're not planning on upgrading, you're probably better off with a different cooler that fits more properly, as any cooler can cool this card.

If you're planning on upgrading to the 9800 at some point in time, like I am, I'd say get the HP80-C. You can use it on your new card, and it cools the 9000 just fine. Installation is a bit bumpy, but not all that bad (and I'm not that much of a techy). I'd buy the same thing again if I could change my mind.

Bye, Lucas

 Post subject:
PostPosted: Mon Nov 24, 2003 9:46 am 

Joined: Thu Dec 05, 2002 4:32 pm
Posts: 519
Sounds interesting, but -- to be perfectly honest -- using a ZM80C heatpipe cooler on a Radeon 9000 is extreme overkill...even a Radeon 9000 pro would have been fine with a NB32J (chipset cooler) or just any decent heatsink. My Radeon 9200 runs fanless, as do most Radeon 9000's. I would say that the ZM80C is more appropriate for Radeon 9800+/NVIDIA 5600+ class video cards.

IBM Thinkpad T42p | 15inch 1600x1200 LCD | 2.0GHz Pentium M Dothan | 1GB DDR | 128MB ATI FireGL T2 | 60GB Hitachi HD 7,200RPM w/ 8MB Cache | DVD-RW | IBM Wireless 802.11a/b/g | 6.0 lbs + 4.5 Hour Battery Life

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 8 hours

Who is online

Users browsing this forum: No registered users and 6 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group