It is currently Fri Oct 31, 2014 3:35 am

All times are UTC - 8 hours




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Removable Harddrive bays - experience, opionions?
PostPosted: Thu Sep 26, 2002 7:30 am 
Offline

Joined: Thu Sep 26, 2002 6:42 am
Posts: 27
I'm using the simple IDE plastic bays like this one:

http://store.yahoo.com/directron/mr27.html

I've got two of the bays in my case right now. I'm using IBM 75GXP 7200 rpm drives inside one of them. The other is empty most of the time but sometimes takes another 75GXP. They work fine but now that I'm trying to quiet the system down, I'm thinking of changing them out. First, each bay has a small, somewhat noisy 40 mm fan in the back to keep the drive from overheating. Second, the fans run even if the bay is empty. Looking at how the bay is built I'm not certain the fan is offering a large amout of cooling to the drive anyway. I've looked around a bit and have not found any removeable bays without a fan. I need both bays to be removeable for the work I do, so I'm looking for suggestions on replacing/modifiying.

1. Any removeable drive bays out there without a fan?
2. If not, would it be safe to remove, replace or undervolt it ? (I imagine this would work better with an aluminum bay rather then a plastic one).
3. Any recommendations on a model you've found to be quiet?

_________________
Todd.


Top
 Profile  
 
 Post subject:
PostPosted: Thu Sep 26, 2002 7:48 am 
Offline
Site Admin

Joined: Sun Aug 11, 2002 3:26 pm
Posts: 11916
Location: Vancouver, BC, Canada
They're all about the same, and all have those whiny wee fans -- which usually die after 6 months or less. The fan does provide necessary cooling, though. The plastic case traps the HDD heat, and it gets pretty hot (above 50C) in no time at all without a fan. I have not played around with aluminum ones; these might provide better cooling through conduction into the case chassis so that you can remove the fan safely. But they are usually at least twice the price.

You could also mod your existing removable drive rack by cutting away much of the bottom panel(s), mounting a quiet 80mm fan (@5V) in a free slot just below it, blowing straight up. This fan can be easily suspended with elastic, and will be MUCH quieter than the built-in tiny fan. If the drive bay cover in which the fan is mounted has some slots so you get fresh air in, the drive should run much cooler.


Top
 Profile  
 
 Post subject:
PostPosted: Fri Sep 27, 2002 4:40 pm 
Offline

Joined: Mon Sep 09, 2002 9:53 pm
Posts: 61
Todd,
I too am wrestling with the Mobile Rack demon. I've got racks in all my PCs, and I move drives here and there for backup and transfer purposes, plus I boot to multiple OSs. Great convenience!

Downsides, noise from the fan, plus the HDD is up in front, so if it is noisy, you're more likely to hear it. Other downside is heat. I've been watching DTemp on my drives that have sensors, and they're close to the top edge of the environmental limits!

I just can't give up that damn convenience, though...

I've been considering modding my case to put a blowhole in the top of the case, running the fan at 5-7 volts, and disconnecting the little fans. If that doesn't help, I might construct some sort of ducting around the HDD bays so that the blowhole will draw air in through the front.

Queue


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group