Gigabyte P35-DS3P Fan control issue
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
Gigabyte P35-DS3P Fan control issue
Hi, I just recently got four Nexus Real Silent Case Fans. My plan was to switch over my other fans, Kamakaze 2 fans, and replace them with these nexus fans. Everything has been wired up, all fans are to the mobo header. But i can't seem to control all the fans. I can control the CPU and GPU fan in speedfan, but not the intake or exhaust. I can only monitor the latter 2. I find it hard to believe that there is 4 headers and only two give you fan control. Is something I can do that can control the other fans?
The reason i switched the fans was so that I could have the fans automatically controlled by Bios/software but it dosen't seem the case ATM.
The reason i switched the fans was so that I could have the fans automatically controlled by Bios/software but it dosen't seem the case ATM.
-
- Posts: 419
- Joined: Sun Sep 19, 2004 1:05 pm
- Location: Palo Alto, CA
Re: Gigabyte P35-DS3P Fan control issue
Only the 4 pin headers on Gigabyte P35 motherboards can be controled by software. Other two are only for readout. This is tested on GA-P35C-DS3R v1.1 motherboard. My Speedfan config is on the Speedfan site.joe123 wrote:... But i can't seem to control all the fans. I can control the CPU and GPU fan in speedfan, but not the intake or exhaust. I can only monitor the latter 2. I find it hard to believe that there is 4 headers and only two give you fan control. Is something I can do that can control the other fans?
-
- Posts: 419
- Joined: Sun Sep 19, 2004 1:05 pm
- Location: Palo Alto, CA
-
- Posts: 419
- Joined: Sun Sep 19, 2004 1:05 pm
- Location: Palo Alto, CA
I couldn't find a tutorial for you but here is what you do.
1. Remove all of the wires from both fans at the connectors except for one yellow wire on one fan ( the yellow wire is for RPM Monitoring, so you only need one). You'll need a pin or something small and thin so that you can remove the pins out of the sockets.
2. Solder wires together and then clip the wires back into a fan plug. Done.
If soldering is out of your field or you don't have time, you could buy one of these:
http://www.svc.com/3pinyadapter.html
Not a very good tutorial i know. But it should help you.
1. Remove all of the wires from both fans at the connectors except for one yellow wire on one fan ( the yellow wire is for RPM Monitoring, so you only need one). You'll need a pin or something small and thin so that you can remove the pins out of the sockets.
2. Solder wires together and then clip the wires back into a fan plug. Done.
If soldering is out of your field or you don't have time, you could buy one of these:
http://www.svc.com/3pinyadapter.html
Not a very good tutorial i know. But it should help you.
Speedfan simply detects the third I/O chip output, but can't check if it's connected to actual hardware (which apparently is non existant). And yes, it does suck balls. Who, in their right mind, in this time and age, would put a fan header WITHOUT possibility of regulation (be it voltage or PWM).zorrt wrote:Speedfan detects a third controller on the DS3P board. I don't get why its not enabled. Sucks balls. Guess I'll just get another one of them fanmates for my exhaust to compliment the one I currently have controlling my intake. I used the SYS_FAN2 header to regulate the temps of my hdd.
I'm even considering buying another motherboard (this one also had issues with on-board LAN).
Yea too bad I didn't think about all this fan controlling when I went out and bought the board so now I'm kind stuck with it. I just stared at the third controller and sigh everytime speedfan starts up :] Until I realised I could take it off the display that is.Lurch wrote: Speedfan simply detects the third I/O chip output, but can't check if it's connected to actual hardware (which apparently is non existant). And yes, it does suck balls. Who, in their right mind, in this time and age, would put a fan header WITHOUT possibility of regulation (be it voltage or PWM).
I'm even considering buying another motherboard (this one also had issues with on-board LAN).
The Abit IP35 Pro can control all the fans via software or BIOS. Much better option than the Gigabyte MB IMO.
http://www.xbitlabs.com/articles/mainbo ... pro_7.html
http://www.xbitlabs.com/articles/mainbo ... pro_7.html