Scythe Gentle Typhoon First impressions (pics added 8.8.09)
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- Posts: 4
- Joined: Sun Aug 09, 2009 10:30 am
- Location: Florida, USA
6 Gentle Typhoon fans
Updating. - I put 5 of the Gentle Typhoon 120mm 1150s and one 92mm 1700 in an Antec 902 case. That's one of Antec's gamer cases with a 200mm fan in the top. I pulled all of the Antec fans, closed the top and modded a sealed port for a push-pull on a Scythe Mugen 2 heat sink to vent out the top of the case. I'm running two Asus EAH4770 in Crossfire (GPU on newest 40nm fabrication). The good news is the system runs virtually quiet when idling against ambient room noise. I'm very happy with the Gentle Typhoon fans. Unbelievably smooth fans!
The Gentle Typhoon fans need a formal SPCR review.
- Rand
.
The Gentle Typhoon fans need a formal SPCR review.
- Rand
.
-
- Posts: 4
- Joined: Sun Aug 09, 2009 10:30 am
- Location: Florida, USA
You talkin' to me?RoGuE wrote:pics or it didn't happen...
I'm not boasting my toy but showing is no big deal. I took a bunch of pix along the build for later reference. These are in reverse order. It's not finished by the last image. One of the 120mm 1150s is mounted in the front of the case.
The forum is giving me a problem with the link because I haven't made 3 posts. You'll have to figure it out...
s858.photobucket.
com/albums/ab143/Newk-Yuler/
- Rand
-
- Posts: 1386
- Joined: Fri Jun 18, 2004 6:53 pm
Heh, seems like a lot of good feedback on this fan. My Nexus exhaust fan is nearing its life, it has trouble starting at low voltages and hub noise is increasing, when I touch it I can feel lubrication is gone.
Only problem is I've tried so many fans that I think this might be just another "flavor of the month". I've tried panaflo, silenx, nexus, papst, noctua, various scythe fans, they all sound more or less the same, some are more disappointing than others.
Anyway, on a brighter note, can anyone tell me what kind of RPM do you get around 7 volts with 1150 model? Thanks!
Only problem is I've tried so many fans that I think this might be just another "flavor of the month". I've tried panaflo, silenx, nexus, papst, noctua, various scythe fans, they all sound more or less the same, some are more disappointing than others.
Anyway, on a brighter note, can anyone tell me what kind of RPM do you get around 7 volts with 1150 model? Thanks!
Just wanted to share an observation about the composition of the frame of the Gentle Typhoon fans. I bought one of the 500RPM models a few months ago to use in the top exhaust position of my P183.
Because the corners of this fan are "semi-closed" I had to remove material from two of the corners to use with the clip-style mounting of this fan position (why oh why didn't Antec change this??). When clipping the material away with tin snips, I found that the corners of the fan frame started to crack, as if the composition of the frame is more of a fiberglass than the usual plastic of, say, the S-Flex fans.
I'm not sure what relationship this has to the observations thejamppa made about vibrations, but it would begin to explain them. If anyone else needs to remove material from one of these fans, you would be much better served by a Dremel or file rather than tin snips or clippers.
Because the corners of this fan are "semi-closed" I had to remove material from two of the corners to use with the clip-style mounting of this fan position (why oh why didn't Antec change this??). When clipping the material away with tin snips, I found that the corners of the fan frame started to crack, as if the composition of the frame is more of a fiberglass than the usual plastic of, say, the S-Flex fans.
I'm not sure what relationship this has to the observations thejamppa made about vibrations, but it would begin to explain them. If anyone else needs to remove material from one of these fans, you would be much better served by a Dremel or file rather than tin snips or clippers.
-
- Posts: 27
- Joined: Mon Jul 06, 2009 2:37 pm
- Location: Texas
I'm using the 1850 rpm model as one of my front intake fans on an Antec P183. I find the noise character to be quite pleasing, just a slight woosh of air, at full RPM. My "handemometer" doesn't think it pushes quite as much air as my S-Flex SFF21G, but it is close and is much quieter at full speed (it doesn't have the "propeller" noise the S-Flex has above around 1300 rpm).
I want some more of them, but good luck finding them right now. Everyone's out of stock.
I want some more of them, but good luck finding them right now. Everyone's out of stock.
-
- Posts: 1386
- Joined: Fri Jun 18, 2004 6:53 pm
Got two 1150 versions. Very very low airflow noise, almost none actually, I think very aggressive fan blade shape is what's responsible here. Unfortunately both fans exhibit a very nasty bearing noise. It is quiet, but the noise character is very annoying in a quiet room, like a quiet screech. Real pity considering lack of airflow noise. I've sort of gotten used to it, but I'm looking at different fans now to replace Typhoons.
Very, very nice. You've got the exact foam surround that I had in mind for my next build. It looks great.Newk Yuler wrote:You talkin' to me?RoGuE wrote:pics or it didn't happen...
I'm not boasting my toy but showing is no big deal. I took a bunch of pix along the build for later reference. These are in reverse order. It's not finished by the last image. One of the 120mm 1150s is mounted in the front of the case.
The forum is giving me a problem with the link because I haven't made 3 posts. You'll have to figure it out...
s858.photobucket.
com/albums/ab143/Newk-Yuler/
- Rand
On a pedantic note, that's 2 fans in series. Push-Pull is 2 fans on opposite sides of the sink. One pushing and one pulling. Nothing wrong with that at all - it provides higher static pressure just the same.
I'd like to try this as well. To have reserve power available. I've generally had really good luck undervolting faster fans.Dezeer wrote:Hi
Have anybody tried the 1850rpm version @7V and what it would be compared to a 1450rpm or 1150rpm @12V?I hope it too.JamieG wrote:Sounds like an SPCR review is definitely in order.
Check this info on the Gentle Typhoons. Compare the 1850 running at 5 volts with the other versions of the fan at 5 volts:
http://www.xbitlabs.com/misc/picture/?s ... ig.png&1=1
http://www.xbitlabs.com/articles/cooler ... up_18.html
http://www.xbitlabs.com/misc/picture/?s ... ig.png&1=1
http://www.xbitlabs.com/articles/cooler ... up_18.html
-
- *Lifetime Patron*
- Posts: 130
- Joined: Wed Aug 09, 2006 6:10 pm
- Location: Columbus, Ohio
- Contact:
Gentle Typhoon 1150 rpm
Another observation point. I have two 1150rpm Gentle Typhoons in a new build, inside an SG05 mini-ITX case, one replacing the front fan, and one blowing down through a Coolermaster Geminii S. Both are undervolted though Zalman fanmate, but the BIOS is reporting flaky RPMs (at full speed they're doing 6100 RPM? I don't think so.)
They are generally quiet, but do have a tone, but the tone does disappear. On the first two days I was concerned, but now I don't even notice it until I turn the computer off. Any other noise in the room -- my wife's Apple Time Capsule firing up, the heat-pump/AC starting up -- and it's as good as silent.
They are generally quiet, but do have a tone, but the tone does disappear. On the first two days I was concerned, but now I don't even notice it until I turn the computer off. Any other noise in the room -- my wife's Apple Time Capsule firing up, the heat-pump/AC starting up -- and it's as good as silent.
Re: Gentle Typhoon 1150 rpm
Still no review?
Re: Scythe Gentle Typhoon First impressions (pics added 8.8.
GT's are some of the best fans out there - maybe the best. But in fairness they need to spin faster to move as much air. The large center means that there is more of dead spot - and thus the blades need to go faster to move the same air. This doesn't mean they are a bad fan - on the contrary its possible to use them at speeds that would be horrible for a regular 120mm fan.
The only downside is all but the very fast 30 and 31 seem to be unavailable..
The only downside is all but the very fast 30 and 31 seem to be unavailable..
Re: Scythe Gentle Typhoon First impressions (pics added 8.8.
The higher speeds are to a large extent a result of the lower attack angles of the fan blade... but these are what contributes to their high static pressure performance. So it looks to me that it is an intentional design trade off. You can't get one without the other.GuyClinch wrote:the blades need to go faster to move the same air.
It does appear that their use of real ball bearings may contribute to higher sample variance than other types of designs. I was told by an engineer with some experience in the matter that fans with real ball bearings can be more easily damaged in shipping. And it seems like there are a fair number of online complaints that seem to be attributable to this.
Still they are great fans. I don't think any other fan can compare with them if you are talking about low dB / high static pressure performance. At the same high static pressure environment, they should deliver more CFM with lower noise than other fans. Don't forget that in high static pressure situations, increases in static pressure increase noise, even if you are able to hold the speed constant (sort of like the luffing of a sail at a high attack angle)
You just may have to factor in that you may get install a clunker before you get the right one installed.
Re: Scythe Gentle Typhoon First impressions (pics added 8.8.
I totally agree:
They are great fans - I I found some for a reasonable price I would pick up a bunch. My point is that people are like oh at 1150 its so quiet. Sure. But so are slipstreams at 800. Still a great fan - and the high static pressure make it fantastic for alot of applications.
They are great fans - I I found some for a reasonable price I would pick up a bunch. My point is that people are like oh at 1150 its so quiet. Sure. But so are slipstreams at 800. Still a great fan - and the high static pressure make it fantastic for alot of applications.
Re: Scythe Gentle Typhoon First impressions (pics added 8.8.
There are a few very good silent fans in the <1000rpm range.GuyClinch wrote:I totally agree:
They are great fans - I I found some for a reasonable price I would pick up a bunch. My point is that people are like oh at 1150 its so quiet. Sure. But so are slipstreams at 800. Still a great fan - and the high static pressure make it fantastic for alot of applications.
It's in the upper range of the 1850 where the GT show their best virtues imo. CFM/noise ratio is second to none (esp @10-11v).
Re:
Read this: Oiling an old fanJazzJackRabbit wrote:Heh, seems like a lot of good feedback on this fan. My Nexus exhaust fan is nearing its life, it has trouble starting at low voltages and hub noise is increasing, when I touch it I can feel lubrication is gone.
viewtopic.php?p=541788#p541788
Re: Scythe Gentle Typhoon First impressions (pics added 8.8.
I am on the fence if I should get some of these for my PC or go with noise blocker black silent pros. The NBs are bit more but come with sleeved cables (and two different cable lengths) and also have PWM version..
Re: Scythe Gentle Typhoon First impressions (pics added 8.8.
Either route will be a good decision.GuyClinch wrote:I am on the fence if I should get some of these for my PC or go with noise blocker black silent pros. The NBs are bit more but come with sleeved cables (and two different cable lengths) and also have PWM version..
-
- Posts: 111
- Joined: Thu Jun 25, 2009 1:23 pm
- Location: USA
Re: Scythe Gentle Typhoon First impressions (pics added 8.8.
I use both a GT and a NoiseBlocker Multiframe (which I assume has similar acoustic quality to the Black Silent). Up close, the GT has a smoother and less noticable sound, but the NB is also so quiet I can't hear it over the rest of the computer. I usually keep both running at around 900 RPM. I should note that the GT has a ringing tone at some speeds, and the NB is quiet at all speeds. I would recommend either fan as a good option.