It is currently Fri Aug 01, 2014 4:36 pm

All times are UTC - 8 hours

Post new topic Reply to topic  [ 65 posts ]  Go to page Previous  1, 2, 3
Author Message
 Post subject:
PostPosted: Wed Jun 14, 2006 6:28 am 
Patron of SPCR

Joined: Sun Jul 04, 2004 6:07 am
Posts: 2674
Location: Houten, The Netherlands, Europe
Which is geek speak for saying that for the majority of people this is not possible.

3) MSI RS480M2-IL | A64 3000+ | Freezer 64 | SS-301HT | 7200.7 PATA 40GB
5) Intel D525MW | Intel 320 40GB | Vertex II 180GB

 Post subject: Tradeoffs
PostPosted: Wed Jun 14, 2006 3:45 pm 

Joined: Thu Nov 24, 2005 3:03 pm
Posts: 317
So, user configurable C'n'Q is possible in Linux. It's more difficult, but it is linux after all. There are even kernel patches available to ease the process. Well, you get what you choose.

I'll take the path of least resistance and go with C'n'Q. Nice to know what my options are before buying.

FWIW, I'm quite happy with the Linux vs. Windows tradeoffs. It all comes down to what is most important to you when selecting tools. For me, Linux wins hands-down, despite the downsides.

A discussion of NVidia 6150 boards might also be of interest to readers of this thread --

 Post subject:
PostPosted: Mon Jul 24, 2006 7:52 pm 

Joined: Mon Sep 09, 2002 11:59 pm
Posts: 138
Location: Melbourne, Oz
Good discussion! Going back to quiet performance though, it seems you can run the EN15000 without the fan, although obviously at your own risk, though the thread on this disappeared when got hacked the other week... :(

Better still, this thread reports that the EN works with Speedfan, which is a first for the Epias, and makes it much easier to build a quiet/silent system. Anyone else had experience with Speedfan on the EN boards?

I've been looking at the digital sensors on the M-Cubed site . These use the SM Bus, and so does Speedfan, so I wonder how you might use such sensors using the I2C (SMBus) headers on the Via EN board?

Any guidance much appreciated :)

 Post subject:
PostPosted: Wed Aug 23, 2006 6:31 am 

Joined: Fri Aug 11, 2006 2:11 pm
Posts: 15
Location: New York
leem wrote:
Going back to quiet performance though, it seems you can run the EN15000 without the fan, although obviously at your own risk

The fan on the EN15000 is actually a fairly quiet 40mm unit that can be completely silenced by a Zalman fan controller (it only needs to be turned down about 1/3 to 1/2 way). My experience with the fanless VIA EPIA boards is that the heatsink can get very hot (almost too hot to touch), as can the CPU. Run fanless, CPU temps of 50° C (or higher) aren't unusual. The addition of even the most minimal fan cures this and sends the temps back to 40° C or less, with the heat sink barely warm to the touch.

Otherwise, for basic desktop applications, the review is on target. The C7 is much zippier then conventional benchmarks would suggest. The main issue for some is that there are only 2 SATA headers, but if you don't need any other cards, an SATA PCI adapter is one solution. This would make it more practical to use, say, as a file server since, at idle, it tends to draw under 30W at the outlet.

In practical terms, the C7 has the feel of an 800Mhz - 1Ghz Pentium III, but one that uses half the power.

Update: Using the Zalman fan controller may be problematic, since turning it down too far will keep the fan from starting at all. In practical terms, the fan on the EN15000 can be silenced by even a minimally sound-proof case.

Also, I had to exchange a fanless EPIA SP800E with C3 processor because the SATA headers were defective. The replacement runs noticeably cooler, so there may be some variation in CPU heat output or the way the heatsink is installed.

Further Update: With the installed 40mm fan turned down to about 2500 rpm, CPU temps on the replacement EN15000 board are now about 30° C. However, without additional cooling, Everest reports motherboard temps of as high as 55° C. The addition of a small fan blowing on the board brings this down to the sub-50° C range.

 Post subject:
PostPosted: Fri Oct 27, 2006 1:54 pm 

Joined: Wed May 31, 2006 8:58 pm
Posts: 2
CityK wrote:
It is possible that an HD clip encoded in MPEG 2 — as is likely to be found on upcoming HD DVD and Blue-Ray discs — would have been able to take advantage of the hardware decoder and played back properly.
presently, because of lack of software support, it is not possible to take advantage of the hardware decoder. One only need turn to the disastrous results that SFFtech observed when trying to playback a MPEG-2 based HD clip for confirmation of this fact....sadly, SFFtech was also not aware of the situation regarding no hardware acceleration support – further tainting their conclusions on the platform.

When, and if, support for the hardware acceleration of the CN700 is obtained on a Windows OS, playback of MPEG-2 based HD material should function fine.
Yes, I realize I'm digging in the dirt and pulling up an old thread, but, for the sake of completeness:

As it turns out, there will never be any hardware acceleraton support in the CN700 for HD -- its mpeg2 decoding is limited to 1024x1024. See Thomas' confirmation post here.

So, its software decoding all the way....which, as the above reviews make abundantly clear, is not up to the task. Stupid VIA, what were they thinking.

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 65 posts ]  Go to page Previous  1, 2, 3

All times are UTC - 8 hours

Who is online

Users browsing this forum: Google [Bot] and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group