It is currently Sun Dec 28, 2014 7:09 am

All times are UTC - 8 hours




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: GF3 ti200: can a panaflo be hooked to the fan header?
PostPosted: Tue Jul 29, 2003 2:02 pm 
Offline

Joined: Tue Mar 25, 2003 10:59 pm
Posts: 1356
Location: NorthEast Arkansas, USA
Trying to do something about this whiny little fan that came with this card. I can unplug it and try a panaflo, but I was wondering if the panaflo can be plugged into the header that the tiny fan uses? Is it safe? functional?
Or must I put it in the motherboard instead?

_________________
The Quake III Machine
C2D e6750 @ Gigabyte GA-P45T-ES3G | 8GB GSkill | Venemous X | Asus 560Ti | Corsair 520HX | 750GB Seagate | Antec 300 | Thanks SPCR


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jul 29, 2003 7:54 pm 
Offline
Patron of SPCR

Joined: Thu Mar 13, 2003 2:38 pm
Posts: 677
Location: California, US
I suggest unscrewing the fan and looking at the label on the underside. I think mine was a 40mm Delta. It should list the amps required by the fan, as well as the voltage (which is almost certainly 12V). If the current draw is over 0.1A, then you can safely swap it with an L1A, which I think draws that much current. If the draw is lower, then you might have problems running the Panaflo. My bet is that the little whirling dervish draws more current than the 80mm L1A.


Top
 Profile  
 
 Post subject:
PostPosted: Fri Aug 08, 2003 11:07 pm 
Offline

Joined: Tue Mar 25, 2003 10:59 pm
Posts: 1356
Location: NorthEast Arkansas, USA
I just unplugged the GF3 fan, used a zalman-123 bracket, finessed an 80mm L1A onto it in a parallel fashion with velcro (it's facing the card just as if it were located in the adjacent PCI slot). I must say, I've been in a good mood because of this. It totally eliminated that whiny card fan, making this computer MUCH more quiet.

_________________
The Quake III Machine
C2D e6750 @ Gigabyte GA-P45T-ES3G | 8GB GSkill | Venemous X | Asus 560Ti | Corsair 520HX | 750GB Seagate | Antec 300 | Thanks SPCR


Top
 Profile  
 
 Post subject:
PostPosted: Sat Aug 09, 2003 5:05 pm 
Offline

Joined: Wed Jun 11, 2003 1:59 pm
Posts: 85
So did you just leave the old hsf on there?


Top
 Profile  
 
 Post subject:
PostPosted: Sat Aug 09, 2003 5:08 pm 
Offline

Joined: Tue Mar 25, 2003 10:59 pm
Posts: 1356
Location: NorthEast Arkansas, USA
WannaOC wrote:
So did you just leave the old hsf on there?


Yes I did. It's a PNY graphics card. It has a fairly large heatsink attached to it. In fact, because of the heatsink, I momentarily considered a fanless approach. In the end, I thought better of that idea.

_________________
The Quake III Machine
C2D e6750 @ Gigabyte GA-P45T-ES3G | 8GB GSkill | Venemous X | Asus 560Ti | Corsair 520HX | 750GB Seagate | Antec 300 | Thanks SPCR


Top
 Profile  
 
 Post subject:
PostPosted: Sat Aug 09, 2003 6:14 pm 
Offline

Joined: Wed Jun 11, 2003 1:59 pm
Posts: 85
Just wondering, did your case temp raise, lower, or stay about the same? Also I would love a pic of this little setup as it's either add a wb (50.00) or a L1A (5.00?) to quiet my radeon down a bit.


Top
 Profile  
 
 Post subject:
PostPosted: Sat Aug 09, 2003 11:38 pm 
Offline

Joined: Tue Mar 25, 2003 10:59 pm
Posts: 1356
Location: NorthEast Arkansas, USA
I can take a pic of it tomorrow and email it to you. Or if somebody has a server for upload I'll do that, although the former would be the easiest and quickest.

As for case temps I don't really know. I haven't installed a program that monitors temps but I know I should. I have gamed heavily with it without any sign of problems; this is after a couple of hours of quake 3 team arena. I would be willing to bet that the card actually stays cooler as I have the panaflo at 12 volts and pointing right at the heatsink, hitting a larger area than the original could.

I think the reason the sound is muffled so well probably has to do with location/position of the fan in the case and the melamine foam I have used. I'm going to fanmate it to a lower setting to see if there is any degree of noticable noise reduction. As it is now, I can only hear this computer when I'm within about 2 or 3 feet of it? Beyond 4 feet or so I'm not sure if it's on without looking at the LED. So it could use some more quieting for the strictest of SPCR standards, but this thing is a very quiet machine.

_________________
The Quake III Machine
C2D e6750 @ Gigabyte GA-P45T-ES3G | 8GB GSkill | Venemous X | Asus 560Ti | Corsair 520HX | 750GB Seagate | Antec 300 | Thanks SPCR


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group