It is currently Fri Aug 22, 2014 3:40 pm

All times are UTC - 8 hours




Post new topic Reply to topic  [ 63 posts ]  Go to page Previous  1, 2, 3  Next
Author Message
 Post subject: Re: 8200?
PostPosted: Fri Jan 23, 2009 1:12 am 
Offline

Joined: Tue Feb 13, 2007 7:28 pm
Posts: 1406
Location: USA
warriorpoet wrote:
True, but I'm also trying a 65nm c2d as well. I'm being feisty all-round :lol:

I was referring to the 45nm stock HSF being lower profile than the 65nm HSF. Are you saying you are going to try the chip or the retail HSF? I have trouble believing the latter will even fit . . .


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jan 23, 2009 5:59 am 
Offline

Joined: Sun Jun 24, 2007 3:35 am
Posts: 332
From experience the Intel stock low profile HSF that comes with the Celeron 440 and Dual Core E5200 will fit inside a case with 60mm interior space with about 3mm to spare (e.g. Casetronic 2699), and will definitely not fit in a case with 50mm interior space (e.g. Silverstone ML02/LC19).

According to the SPRC review, the clearance between the PSU and the bottom of the case is 50mm, so the Intel low profile HSF will not fit.


Top
 Profile  
 
 Post subject: PS used elsewhere?
PostPosted: Fri Jan 23, 2009 9:34 am 
Offline

Joined: Fri Jul 18, 2003 11:59 am
Posts: 220
Location: Vancouver, B.C.
It seems to me that one of the real eye-openers of this review is the silence of the Allied AL-8250SFX 250W PS used in the Apex case. Does anyone know if Apex uses this PS in any of their other cases - perhaps ones with a bit more clearance for more powerful mb's and heatsinks?

The ad here:

http://www.eworldsale.com/apex-allied-a ... 20246.html

, suggests that this is the PS used in most HP/eMachines microATX systems?


Top
 Profile  
 
 Post subject: Re: 8200?
PostPosted: Fri Jan 23, 2009 7:22 pm 
Offline

Joined: Wed Jul 20, 2005 10:56 am
Posts: 323
Location: USA
jessekopelman wrote:
warriorpoet wrote:
True, but I'm also trying a 65nm c2d as well. I'm being feisty all-round :lol:

I was referring to the 45nm stock HSF being lower profile than the 65nm HSF. Are you saying you are going to try the chip or the retail HSF? I have trouble believing the latter will even fit . . .
Absolutely no, no. I'm trying this one exhausting toward the side-mounted 120mm fan.

http://www.newegg.com/Product/Product.a ... 6835114075

All else fails I'll undervolt it as far as is prudent.

_________________
ATCS840/ Seasonic X-750/ 2500k 4.4 GHz (Koolance CPU-370)/ Gigabyte z68xp-ud4/ eVGA 570 865,1730,1950 (Koolance VID-580)/ 8Gb G.Skill DDR3 1866/ Corsair Force 3 120Gb, Samsung 470 128 Gb, Scorpio Black 750 2.5" (Quiet Drive)/ EK DCP-2.2 (res., gel-stuff)/ XSPC RX360, Swiftech MCR220QP/ 3 Scythe GT ~300-550RPM, 3 NB Multi-frame ~400-600RPM, 3 230mm 300RPM-> Lamptron FC-4/ Akasa AcoustiPack


Top
 Profile  
 
 Post subject:
PostPosted: Sat Jan 24, 2009 8:11 am 
Offline
Patron of SPCR

Joined: Sat Dec 25, 2004 10:48 am
Posts: 26
Location: Berkeley, CA
I've built three boxes now with the Apex MI-100 case http://www.newegg.com/Product/Product.a ... 6811154084 which is almost identical to this case. I figured out the 120mm fan trick early on - I think a NewEgg product review mentioned it.

I used the D945GCLF2 and of course hated that 40mm hair dryer fan on the chipset. I'm using my little boxes for NAS, Windows 2003 server and Linux server for my home network, so they don't get loaded real heavily for the most part. I found that in my application I could just unplug the chipset fan without any apparent consequences. The airflow from the orange 120mm Yate Loon fan http://www.svc.com/d12sl-12-or.html wedged in the side blows directly toward the chipset heatsink, which is apparently enough airflow to prevent meltdown.

But I wanted to find a more efficient chipset cooler. The first thing that I tried was a Zalman ZM-NBF 47 http://www.newegg.com/Product/Product.a ... 6835118014. Bad choice. The spring clip attachments face the wrong direction and a couple of the fins interfere with the RAM. After bending some fins and cobbling together clips that would hold it down, I got it in place and working. But that was far from an ideal solution, so I kept looking.

The next thing I tried was a SilenX IXN-40C http://www.newegg.com/Product/Product.a ... 6835226019. A lot more expensive, but hey, the clips face the right direct and it fits with the stock power supply. Thus far the SilenX is the best solution I have found. Installation is painless and I am thinking that heat dissipation should be very good since it's full copper. I haven't stress tested it, but it has been stable even with the 120mm fan undervolted by way of a Zalman FanMate 2 http://www.svc.com/zm-fanmate2-75.html.

_________________
-- Current sorta silent boxes --

Windows Server 2003: Apex MI-100, Intel D945GCLF2, SilenX IXN-40C, Yate Loon 120mm, FanMate 2, 2GB RAM, 500GB SATA

OpenFiler NAS: Apex MI-100, Intel D945GCLF2, Zalman ZM-NBF47 (bad idea), Yate Loon 120mm, FanMate 2, 512MB RAM, 1.5TB SATA, SATA hotswap bay

Ubuntu Server: Apex MI-100, Intel D201GLY2, Yate Loon 120mm, FanMate 2, 1GB RAM, 250GB SATA


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 28, 2009 6:06 am 
Offline

Joined: Mon Dec 12, 2005 5:01 am
Posts: 443
Location: Foster City, CA
the geek in me really wants to try this for a WHS build....but there's a voice inside my head that keeps saying that if I don't get the HP Media Server, I will regret it. :wink:


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 28, 2009 3:11 pm 
Offline

Joined: Tue Feb 13, 2007 7:28 pm
Posts: 1406
Location: USA
aztec wrote:
the geek in me really wants to try this for a WHS build....but there's a voice inside my head that keeps saying that if I don't get the HP Media Server, I will regret it. :wink:

Is the voice in your head sponsored by HP? If so, do you see a cut of that? :D

Anyway. I'd think it would be the opposite. You might be perfectly satisfied by the HP, but wouldn't you always regret that you never had the fun of DIY?


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jan 29, 2009 7:34 am 
Offline

Joined: Tue Sep 16, 2008 11:47 pm
Posts: 47
Location: UK
Has anyone found a good UK retailer for this yet?

_________________
Save a tree - use MoDT! Desktop: Core 2 Duo T7200 + MSI 945GT Speedster // Desktop2: Core 2 Duo T5600 + Aopen i945GTm-VHL // HTPC: Core Duo T2400 + Aopen i945GMm-HL // Server: Intel D945GCLF2 // CarPC: Intel D201GLY


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jan 29, 2009 9:38 am 
Offline

Joined: Mon Jan 13, 2003 9:20 am
Posts: 742
Location: UK
wywywywy wrote:
Has anyone found a good UK retailer for this yet?


"good uk retailer"... any oxymoron surely ;)

It's going to be really expensive here, until the Pound picks up.

_________________
http://world3.net


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jan 29, 2009 3:29 pm 
Offline

Joined: Fri Feb 23, 2007 11:55 pm
Posts: 410
miks2u wrote:

The next thing I tried was a SilenX IXN-40C http://www.newegg.com/Product/Product.a ... 6835226019. A lot more expensive, but hey, the clips face the right direct and it fits with the stock power supply. Thus far the SilenX is the best solution I have found. Installation is painless and I am thinking that heat dissipation should be very good since it's full copper. I haven't stress tested it, but it has been stable even with the 120mm fan undervolted by way of a Zalman FanMate 2 http://www.svc.com/zm-fanmate2-75.html.


x2 for SilenX IXN-40C. i am usually not a big fun of SilentX products but this one is actually pretty good - good cooling ability in a small package.

_________________
dothan 730 @ 2.6Ghz l p4c800ed l 4x512MB bh5 2-2-2-5 5:4 ~3v Antec Neo 480
e6600 @ 3.6GHz l P5W64 WS Pro l 4x1GB D9GMH (B6-3) 3-3-3-3-12 4:3 2.2v l PCP&C 750


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jan 30, 2009 9:30 pm 
Offline
Patron of SPCR

Joined: Sat Dec 25, 2004 10:48 am
Posts: 26
Location: Berkeley, CA
I clicked off some quick snapshots of my Server 2003 build and stuck them on Flickr. See http://www.flickr.com/photos/10625552@N ... 138962843/ to see how the SilenX heatsink fits in the case.

_________________
-- Current sorta silent boxes --

Windows Server 2003: Apex MI-100, Intel D945GCLF2, SilenX IXN-40C, Yate Loon 120mm, FanMate 2, 2GB RAM, 500GB SATA

OpenFiler NAS: Apex MI-100, Intel D945GCLF2, Zalman ZM-NBF47 (bad idea), Yate Loon 120mm, FanMate 2, 512MB RAM, 1.5TB SATA, SATA hotswap bay

Ubuntu Server: Apex MI-100, Intel D201GLY2, Yate Loon 120mm, FanMate 2, 1GB RAM, 250GB SATA


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jan 30, 2009 11:46 pm 
Offline
*Lifetime Patron*

Joined: Sun May 21, 2006 9:09 am
Posts: 1809
Location: Northern California.
be mighty interesting to see someone put the psu down low, in front and use a real HS..looks like tons of wasted space under the intended hdd location. and it would leave room for a nice exhaust out the old psu hole.



or did i miss that suggestion already...?


:oops:


Top
 Profile  
 
 Post subject:
PostPosted: Sun Feb 01, 2009 8:52 pm 
Offline

Joined: Wed Jul 20, 2005 10:56 am
Posts: 323
Location: USA
Good news/ bad news:

1. the Dynatron side-exhausting is a resounding failure- ridiculously noisy on startup, gets quieter, but has the most unpleasant grinding sound known to man. Simple mounting mechanism is offset by horrendous temps: 58-74c-- yes this is a good mount with MX-2.Update: I remounted with MX-2. I was mistaken earlier-- I had used the stock thermal goop. Don't use the stock thermal goop. Temps are 51-71c now (Intel CPU Burn-In), and the CPU fan ramps only slightly.

2. There is no easy way to soft-mount a 3.25" drive permanently with a DVD drive installed. I thought about putting it on the floor resting on foam, but the mobo gets in the way. Quiet HDD in this enclosure pretty much means using a notebook drive suspended.

3. PSU ramps less and the case temp is lower (5-9c) with the 120mm fan pushing air through the gap between the DIMMs and past the chipset sink. Noise level for intake is significantly higher than with the fan reversed to exhaust, even at 5v.

4. Future revisions should include door mount for a slim 120mm fan and more open grill work. This could be a very, very nicely ventilated case with a bottom intake vent, as well.

5. A bit of PaxMate on the solid wall, top and bottom works wonders for perceptible fan frequencies, especially for the annoyingly grindy Dynatron cooler (how I despise it). I wish it did the same for HDD noise levels...

If anyone has a suggestion for a nice, quiet low-profile side-vent heatsink, please let me know.

_________________
ATCS840/ Seasonic X-750/ 2500k 4.4 GHz (Koolance CPU-370)/ Gigabyte z68xp-ud4/ eVGA 570 865,1730,1950 (Koolance VID-580)/ 8Gb G.Skill DDR3 1866/ Corsair Force 3 120Gb, Samsung 470 128 Gb, Scorpio Black 750 2.5" (Quiet Drive)/ EK DCP-2.2 (res., gel-stuff)/ XSPC RX360, Swiftech MCR220QP/ 3 Scythe GT ~300-550RPM, 3 NB Multi-frame ~400-600RPM, 3 230mm 300RPM-> Lamptron FC-4/ Akasa AcoustiPack


Top
 Profile  
 
 Post subject:
PostPosted: Sun Feb 01, 2009 10:26 pm 
Offline

Joined: Wed Jul 20, 2005 10:56 am
Posts: 323
Location: USA
another part of the thermal puzzle solved:

There is a significant airflow short-circuit in the empty area next to that used by the 120mm fan as installed by SPCR. Covering that open area (I used some scrap PaxMate) so that only the 120mm fan is open reduces noise and improves board + CPU temps noticeably. It also reduces PSU ramping which, in this particular sample, is remarkably unobtrusive as-is.

FWIW, I've found using the single expansion slot as an intake works best to keep board + CPU temps low and block noise pathways. Leaving the other side open as well provides a nice intake at idle and exhaust at load (depending on CPU fan speed).

Now if I can only solve the HDD and CPU grindy fan issues...

_________________
ATCS840/ Seasonic X-750/ 2500k 4.4 GHz (Koolance CPU-370)/ Gigabyte z68xp-ud4/ eVGA 570 865,1730,1950 (Koolance VID-580)/ 8Gb G.Skill DDR3 1866/ Corsair Force 3 120Gb, Samsung 470 128 Gb, Scorpio Black 750 2.5" (Quiet Drive)/ EK DCP-2.2 (res., gel-stuff)/ XSPC RX360, Swiftech MCR220QP/ 3 Scythe GT ~300-550RPM, 3 NB Multi-frame ~400-600RPM, 3 230mm 300RPM-> Lamptron FC-4/ Akasa AcoustiPack


Top
 Profile  
 
 Post subject: My hard drive mounting solution
PostPosted: Fri Feb 06, 2009 11:35 pm 
Offline

Joined: Sun May 08, 2005 9:39 am
Posts: 27
Location: Santa Cruz, CA
I got the MI-008 and D945GCLF2 for a home file server after reading this review, and I'm quite pleased with it. However, like the review said, a hard-mount drive really makes a racket when seeking. Completely unacceptable, sounds like a tin drum...

Thinking about a solution that would muffle the drive and allow me to mount 2 drives, I realized that I could use the unused plastic rails and trays from the upper rack in my P180... :lol:

It worked out nicely I think, and it's always nice when you can recycle parts! Check out the pictures at http://governator.ucsc.edu/photo_album/folder/569565869

cheers,

/Patrik


Top
 Profile  
 
 Post subject:
PostPosted: Sat Feb 07, 2009 7:32 am 
Offline

Joined: Sun Jun 24, 2007 3:35 am
Posts: 332
I discovered a potentially cool mod to this case:

The green power LED behind the power switch can be removed and inserted into a socket conveniently located on the piece of clear plastic on the right side of the case that transmits light. So you can get you power light on the right side. But that's not the cool mod I have in mind.

With the power LED removed from its original socket, you could put in its place an IR receiver sensor. So if you have an external or internal USB IR reciever, you can extend the IR sensor (typically about the same size as an 1/4" diameter LED) and fit it behind the power switch. Of course this project will require some soldering work.


Top
 Profile  
 
 Post subject:
PostPosted: Fri Feb 13, 2009 6:05 am 
Offline

Joined: Sun Jun 24, 2007 3:35 am
Posts: 332
I just finished this mod and turned an external USB IR receiver into an internal unit.

It involved some soldering to extend the IR receiver module (that's the 3-pin device with dome shaped lens) and the status LED (a total of 4 wires - Vcc, Gnd, IR module signal out, and LED out), enlarging the hole behind the power button, and fitting the combined IR module and LED inside the power button.

There's plenty of space inside the power switch to house both the IR receiver module (similar to this) and a small LED. To my surprise the small areas of clear plastic on the face of and around the the power button are sufficient to provide excellent IR reception. The best part of the mod was that it did not involve making any external cosmetic modifications to the case.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Mar 31, 2009 1:03 pm 
Offline

Joined: Tue Mar 31, 2009 1:01 pm
Posts: 6
Location: NY
If I am not concerned about having a CD/DVD in that bay, what is the possibility of getting 3 or possibly 4 SATA HDDs in this box? Do I have enough power and cables?


Top
 Profile  
 
 Post subject: Re: Fan Fight
PostPosted: Mon Apr 13, 2009 7:58 am 
Offline

Joined: Wed Apr 08, 2009 11:40 am
Posts: 1
Location: usa
Broadleaf wrote:
The fans are fighting against each other for air. The chipset fan orientation should be changed to blow upwards. If a case fan is added, then it should blow inwards.


can't the Apex PSU be opened up and the fan turned around so that it blows out? what would be the harm in doing that? anybody know?


Top
 Profile  
 
 Post subject: corsairf4u - subject: Fan Fight
PostPosted: Mon Apr 13, 2009 7:02 pm 
Offline

Joined: Mon Dec 17, 2007 8:57 pm
Posts: 29
Location: Calgary, Alberta, Canada
Yes, the fan can be easily flipped around so that it blows towards the CPU cooler. (And as always the reminder: "When you break the seal on the PSU case your warranty has ended.") The air will be heated up a few degrees passing through the power supply. Depending on the CPU and heat sink, you probably won't need the tiny noisy fan on the CPU.

_________________
My Quiet System: Antec P180 spcr_edition, Antec Phantom 500, ASUS P5WDG2 WS PRO, Pentium Dual Core E2220, Scythe NINJA, Sapphire HD 3850, 2 of WD RE 500 MB.


Last edited by Broadleaf on Sat Jun 06, 2009 9:31 am, edited 2 times in total.

Top
 Profile  
 
 Post subject:
PostPosted: Sun May 31, 2009 10:44 pm 
Offline

Joined: Sat May 21, 2005 3:35 am
Posts: 4
Location: Toronto, Ontario, Canada
I have this case. Oooo does it make noise while recording to an HDD. But forget that.

For the NB I used a the Enzotech CNB-R1 Rev A $20 CND comes with Artic Silver Paste. The clip is reversed, so I used the stock Intel clip, bent a wack load of pins, but bent them back after the install to paintstaking precision to fit the Scythe Mini Kaze HTPC Silent Mini Fan 40MM 3500RPM 4.1CFM 14DBA (just incase it gets too hot in the summer, no a/c here).

The Enzotech is good enough to run passive. I might get another for the CPU for shits n giggles. I'm putting my PWM-200 in soon.

The OS drive is just a 133x 8GB CF $25 card on an IDE adapter.
And there is a low profile 2GB stick of ram in it I picked up for $20

Since I'm ditching the OEM PSU, I'm going to CUT the case in half, and 5.25 and 3.5 front bays so they are directly over top the mainboard. Now where is did that dremel go...


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jun 25, 2009 5:39 pm 
Offline

Joined: Thu Jun 25, 2009 5:24 pm
Posts: 4
Location: USA
I was thinking of pairing this case up with the Zotac IONITX-A-U. Since this motherboard comes with an external PSU, I would not have to use the case's PSU. So I was thinking of covering the leftover hole from the PSU with something but not sure with what. Any ideas?


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 10, 2009 6:39 pm 
Offline

Joined: Tue Oct 31, 2006 10:41 am
Posts: 7
For drive mounting, I've been using 1/8" shock cord (from REI) to support the drives. I haven't decided how I'm going to hang a pair for ZRAID, but this works nicely for me.

I'm using Scythe MiniKaze 40x40x10 from Petra's Tech Shop to replace the heatsink fan. It makes a huge difference for under $5.

I'm frustrated by the noise from the 120mm fan on the side with the case on. Its great with it off, but as soon as the grille is in place, you get a significant increase in noise.

These cases don't really support even the D945GCLF2 without a case fan of some sort. The temps under load just get to high.


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 10, 2009 6:39 pm 
Offline

Joined: Tue Oct 31, 2006 10:41 am
Posts: 7
Here are the photos

Image

Image


Top
 Profile  
 
 Post subject: Power measured Deer/Allied DR-8250SFX versus FSP90 (PICO)
PostPosted: Wed Aug 05, 2009 4:15 am 
Offline

Joined: Wed Aug 05, 2009 3:29 am
Posts: 3
Location: Utrecht, Netherlands
For a camera application, we were looking for a compact , low power PCI express x4 platform. At the time of selection, the POV MB330 ION-ATOM seemed the only platform available (intel arrandale and atom pineview were not released yet) providing these features. We did the following power measurements:

MB : Point Of View, POV ION-MB330 (miniITX, atom 330 + ION chipset and PCI express x16)
http://www.pointofview-online.com/showr ... duct_id=97
SSD: Intel, X25M-160 G
MEM: 1x 2GB SODIMM PC2-5300 (667MHz)
PS1: Deer/Allied DR-8250SFX (POV ION-CS330 system came with SPIRE/APEX case with PS1 installed)
PS2: FSP90 (90W, Pico-like PS)
measurement device: Voltcraft Energy check 3000 @ 230V

Power with XP running idle:
PS1: 28W
PS2: 20W !!!!
PS2: 22.6W (2 x 2GB SODIMM PC2-6400 (800MHz) )

Now with frame grabber installed (also idle): Dalsa X64 Xcelera-CL PX4, PCI express x4
PS1: 37W
PS2: 30W

I exprerimented also with other supplies. The results can be found at:
http://www.phys.uu.nl/~rossewij/PCpower.doc
http://www.phys.uu.nl/~rossewij/IONatom330PICO.jpg

Conclusion:
* (FSP) Pico PS significant more efficient, especially at lower powers.
* 2G additional memory draws 2.5...3W more
* POV MB330 ION-ATOM with 2 Gbye memory combined with a pico PS consumes < 20 Watt idle !!!!!.
The POV MB330 ION-ATOM (cost around 120 euro) makes it possible to build a small/compact, low priced, low power ( < 20W !!! idle with pico PSU ) system with PCI express x16 functionality.


Last edited by rossewij on Tue Dec 22, 2009 4:06 am, edited 7 times in total.

Top
 Profile  
 
 Post subject: cooling a C2D?
PostPosted: Wed Sep 02, 2009 11:44 am 
Offline

Joined: Fri Jul 18, 2003 11:59 am
Posts: 220
Location: Vancouver, B.C.
Did anyone ever figure out how to effectively, and silently, cool a C2D in one of these cases?

Intel has a nice budget LGA775 mini-itx mb now:
http://www.newegg.com/Product/Product.a ... 6813121381

Combined with an e6300 CPU, and a 30 GB SSD, it could be a small, snappy and quiet system if the CPU could be cooled. Any success stories out there?


Top
 Profile  
 
 Post subject:
PostPosted: Tue Nov 17, 2009 3:04 am 
Offline

Joined: Mon Mar 24, 2008 12:49 am
Posts: 5
Location: Canberra
So,
be warned, these case have just been released in Australia.
There is good news and bad news.
Good news, no need to worry about the chipset fan.
Bad news is that is because the PSU drowns it out.
Instead of the AL-8250SFX we get a SL-B220SFX, no obvious branding... but may be by SolyTech...
Time for me to buy a pico psu....

_________________
Antec Fusion, Seasonic S12+ 550W PSU, Intel Core 2 Duo E8200 2.66GHz, Scythe Ninja Mini Heatsink (no fan), 2x Noctua NF-S12, Asus P5K-VM, 2GB PC5300 RAM, Gigabyte 8600GT Passive, Hauppauge, 2x WD 1TB GP HDDs, SoundPad


Top
 Profile  
 
 Post subject:
PostPosted: Sun Nov 22, 2009 7:21 am 
Offline

Joined: Wed Apr 22, 2009 7:06 am
Posts: 109
Location: Austin, TX
brucesm wrote:
So,
be warned, these case have just been released in Australia.
There is good news and bad news.
Good news, no need to worry about the chipset fan.
Bad news is that is because the PSU drowns it out.
Instead of the AL-8250SFX we get a SL-B220SFX, no obvious branding... but may be by SolyTech...
Time for me to buy a pico psu....

Ouch. :( I've even got the bundled Allied PSU sitting on top of the case and it's not all that noticeable (. Thanks for the heads up for others on that side of the globe. I wonder how wide the area is with this alternate model, all a Google search turned up was some Australian sites, plus a Chinese or two (though pretty much always these are Chinese-made, so that would make sense). If it's truly just Australia and everyone else gets the Allied, then what's up with that? :?


Top
 Profile  
 
 Post subject:
PostPosted: Fri May 14, 2010 6:09 am 
Offline

Joined: Wed Feb 09, 2005 10:39 am
Posts: 57
frank2003 wrote:
I just finished this mod and turned an external USB IR receiver into an internal unit.

It involved some soldering to extend the IR receiver module (that's the 3-pin device with dome shaped lens) and the status LED (a total of 4 wires - Vcc, Gnd, IR module signal out, and LED out), enlarging the hole behind the power button, and fitting the combined IR module and LED inside the power button.

There's plenty of space inside the power switch to house both the IR receiver module (similar to this) and a small LED. To my surprise the small areas of clear plastic on the face of and around the the power button are sufficient to provide excellent IR reception. The best part of the mod was that it did not involve making any external cosmetic modifications to the case.
Yes thta does sound cool! I realize this was posted 6 months ago, but if you are still around, I would like more details of this mod (functionality added & how-to). Could you post them? Does that mod allow you to power the PC on/off with the IR remote?

Might make the most sense to start a new thread -- but then please post link to it here, I will watch this thread so I can get notice if you post again. Thanks!


Top
 Profile  
 
 Post subject:
PostPosted: Fri Sep 24, 2010 6:36 pm 
Offline

Joined: Wed May 04, 2005 6:40 am
Posts: 5
Location: Boston, MA
puddnhead wrote:
Yes thta does sound cool! I realize this was posted 6 months ago, but if you are still around, I would like more details of this mod (functionality added & how-to). Could you post them? Does that mod allow you to power the PC on/off with the IR remote?

Might make the most sense to start a new thread -- but then please post link to it here, I will watch this thread so I can get notice if you post again. Thanks!

Count me in on more info too, this sounds amazing.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 63 posts ]  Go to page Previous  1, 2, 3  Next

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group