It is currently Fri Sep 22, 2017 3:42 am

 All times are UTC - 8 hours

 Page 1 of 1 [ 4 posts ]
 Print view Previous topic | Next topic
Author Message
 Post subject: Achieving 6 V from serial connection in practice.Posted: Sun Oct 24, 2010 8:04 am
 Friend of SPCR

Joined: Fri Jul 02, 2010 4:41 am
Posts: 709
Location: Denmark
I've read somewhere on SPCR that by connecting two fans to a single molex in serial, each fan will have a voltage at 6 V.

But how do I do that in practice?
And is it possible when using a molex to 3-pin converter?

_________________
Cooler Master Elite 341, Athlon II X3 425, Radeon 5750 (passive, fan zip-tied on), Crucial M4 64 GB.
Cooling: AC Alpine 64 Pro, rear exhaust Scythe Slipstream 800 rpm @ ~5 V

"SSD's: The difference between a casual jogger and a dog chasing a ball"

Top

 Post subject: Re: Achieving 6 V from serial connection in practice.Posted: Sun Oct 24, 2010 9:43 am

Joined: Wed Aug 15, 2007 7:37 pm
Posts: 222
Location: Melbourne, Victoria, Australia
It's just basic electrical theory. To do this, you'll need two identical fans, since resistance for different fans are not the same. You can figure out the resistance by looking at the current or wattage of the fan. For example, if the fan spec is 15 watts (that would be some crazy high flow fan), you would find the current with P=VI, or Power equals Voltage (12V in this case) times Current:
Code:
P=VI
I=P/V
I=15/12
I=1.25A

So 15watts would equal 1.25 amps. Now we have the current, we'd use V=IR, or Voltage equals Current (1.24 amps) times Resistance:
Code:
V=IR
R=V/I
R=12/1.25
R=9.6

So this 15 watt fan would be 9.6 Ohms. If I hook this in series with say, this 120mm fan that runs on 0.3A (40 Ohms), the two fan resistances are quite imbalanced. Kirchhoff's circuit laws come into play, and you'd see that the large 15 watt fan takes about 80% of the voltage (so to speak), and would run at ~9.7V while the 120mm fan would only get ~2.3V.

So, unless you use two identical or very similar resistance fans, the voltage would be unbalanced. Now, if you already have two fans in mind, what you'll need to do is to remove the pins from the molex connector on both fans, and hook them up so instead of being in parallel, they would be hooked up in series.

And um...long story short, I guess if you don't know what you're doing, I'd recommend you stick with fan speed 'adaptors' that use simple resistors such as these, or fan speed controllers, such as these or these.

Top

 Post subject: Re: Achieving 6 V from serial connection in practice.Posted: Sun Oct 24, 2010 2:01 pm

Joined: Wed Jun 02, 2010 12:45 am
Posts: 59
Location: New Zealand
It's not hard to learn how to make electrical joins.

In practice, if you are OK hardwiring the fans, then what you can do is:

1. Cut the Ground wire from one of the fans (let's call it A). Ground is usually black. We'll keep the plug for this fan.

2. Cut all the connections from the other fan. (let's call it B). We'll discard the plug for this fan.

3. Connect the 12v wire from "B" to the ground wire of A's fan.

4. Connect the ground wire from "B" to the ground wire of A's plug.

If you want to know how to actually make electrical connections, it's relatively simple.

To be honest, the soldering mostly adds mechanical strength rather than electrical - i.e, if you won't be tugging on the wires in installation, you can probably get away without soldering (but soldering is best, and it's a good skill to learn)

Top

 Post subject: Re: Achieving 6 V from serial connection in practice.Posted: Sun Oct 24, 2010 8:28 pm

Joined: Wed Nov 10, 2004 1:44 pm
Posts: 199
Location: Sweden
I've done something similar, but with a Y-splitter for 3-pin. This way you don't have to butcher the fan wires.

Cut the red wire to one of the plugs, and the black wire from the other. Strip the insulation on the plug wires some 10 mm, and connect them. Solder, or just cover with electrical tape.

Current will now flow from connector, via red wire into the first fan, drop 6 volts coming back in the black wire, continue in the red wire to second fan, and finally deliver 0V to black wire in connector.

/d

_________________
[CPU: 2.4 GHz P4 Northwood w. AC Freezer 4 (fanless-Bluefront PSU mod inspired) / MB: ABIT VT7 (Via PT880) / GPU: ATI Radeon X800XL w Zalman ZM80D-HP / HDD: Seagate Barracuda IV SATA 80GB / CD: Samsung CD-DVD combo / Seahawk ALU Case / PSU: FSP 350-THN (fan mod-Everflow connected to CPU fan header)

Top

 Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost timeSubject AscendingDescending
 Page 1 of 1 [ 4 posts ]

 All times are UTC - 8 hours

#### Who is online

Users browsing this forum: Yahoo [Bot] and 4 guests

 You cannot post new topics in this forumYou cannot reply to topics in this forumYou cannot edit your posts in this forumYou cannot delete your posts in this forumYou cannot post attachments in this forum

Search for:
 Jump to:  Select a forum ------------------ Rules & Announcements    SPCR Announcements    Forum Rules Silent PC Discussions    Donate for Reviews    SPCR Article Discussion    Newcomers Briefing Room    System Advice / Troubleshooting    The Silent Front    General Gallery    Deals, Vendors and Classifieds    Consumer Advocacy    Green Computing Silent Hardware    Quiet Prebuilt, SFF and Barebones Systems    Cases and Damping    Power Supplies    CPUs and Motherboards    CPU Cooling    Watercooling    Fans and Control    Video Cards & Monitors    Silent Storage    Networking    Notebook Systems    User Reviews SPCR Community    Audio Crafts    SPCR's [email protected]    Off Topic Site Feedback    Site Feedback    Test Forum