Fractal R3
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
Fractal R3
Ok here's my Fractal R3....The stock fans are too loud, I replaced them with my trusty Scythe Sflex 800 rpm fans. And as far as the sound dampening material in the case, well I think this case is as quiet as an antec P180 without it...
Uploaded with ImageShack.us
Uploaded with ImageShack.us
Re: Fractal R3
Very nice and clean looking build you've got there! I may have to reconsider the Fractal R3 for my build.. the cable management grommets are an immense help.
That SSD in the bottom of the hard drive cage looks awfully lonely.. haha.
That SSD in the bottom of the hard drive cage looks awfully lonely.. haha.
-
- Posts: 91
- Joined: Wed Oct 06, 2010 6:32 am
- Location: new york
Re: Fractal R3
You're making me jealous. My new build is going to be a fractal design define with a seasonic X series too. I hope mine looks as nice as yours.
Is the SSD attached to the case or is it just laying in that tray?
thanks
Is the SSD attached to the case or is it just laying in that tray?
thanks
Re: Fractal R3
Its attached to the drive bay And yes it is lonely their.
-
- Posts: 450
- Joined: Mon Mar 29, 2010 2:47 am
- Location: Bratislava, Slovak Republic
Re: Fractal R3
You should do the same i did. Remove all the unused drive bays. Only if the whole 3,5" drive bay construction wouldn't be riveted but only screwed in, i would remove it ASAP.
Re: Fractal R3
1/8" drill bit solves the rivet problemfaugusztin wrote:You should do the same i did. Remove all the unused drive bays. Only if the whole 3,5" drive bay construction wouldn't be riveted but only screwed in, i would remove it ASAP.
-
- Posts: 450
- Joined: Mon Mar 29, 2010 2:47 am
- Location: Bratislava, Slovak Republic
Re: Fractal R3
Of course it does... Except with my skills, i would end up drilling through front panel and scratching the paint all over .Meato wrote:1/8" drill bit solves the rivet problemfaugusztin wrote:You should do the same i did. Remove all the unused drive bays. Only if the whole 3,5" drive bay construction wouldn't be riveted but only screwed in, i would remove it ASAP.
Re: Fractal R3
I'm planning on doing a R3 build too, shitty to hear that the fans are no good. I have heard reports of the scythe clicking at low rpm, is that the case with the ones you have? If not I will def be duplicating that build lol.
Re: Fractal R3
I saw that in a review as well. But my Scythe Sflex 800 rpm fans make no such noise that I can hear anyway. They are dead quiet...
-
- Posts: 91
- Joined: Wed Oct 06, 2010 6:32 am
- Location: new york
Re: Fractal R3
Did you try using the included fan controller to slow down the fans?
Re: Fractal R3
Nice one. Welcome to the R3 club
Re: Fractal R3
The included fans at 5V can be used as intakes fairly well. They tick a little but you'd have to be very close to hear that from behind the door.
On my white R3 the rear fan grating proved to be too restrictive even for an 800 RPM Slip Stream at full speed, possibly due to the thicker paint but mostly because that particular vent has a more restrictive design.
On my white R3 the rear fan grating proved to be too restrictive even for an 800 RPM Slip Stream at full speed, possibly due to the thicker paint but mostly because that particular vent has a more restrictive design.
Re: Fractal R3
I didn't try the fan controller. I like to keep the wires and extra's in my case to a bare minimum. I've had these Sflex fans for about 3 years or so and they have worked extreme well. I just added a 27 inch monitor to my setup and its really nice
Re: Fractal R3
I have a question for Define R3 owners.. how do you find the silicone HDD cage grommets for isolation? Would they be able to keep HDDs with relatively little vibration in check?
Re: Fractal R3
The grommets are good enough to quiet todays 5400 RPM drives like the WD or Samsung "greens". I' using three HD204UI right now. Most 7200 RPM 3,5" drives will vibrate too heavily.
-
- Posts: 3
- Joined: Sun Mar 13, 2011 6:09 pm
Re: Fractal R3
can you tell us the exact video card model and also what is your cpu cooler ?
I would like to use the asus GTX 570 DirectCU II in a fractal design R3, however the card measures 292mm and the maximum card lenght for that case is apparently 290mm...
also im trying to figure out which heatsink to use, which would give enough clearance for my 40mm ram.
thx
I would like to use the asus GTX 570 DirectCU II in a fractal design R3, however the card measures 292mm and the maximum card lenght for that case is apparently 290mm...
also im trying to figure out which heatsink to use, which would give enough clearance for my 40mm ram.
thx
Re: Fractal R3
My video card is the Msi 6870 fitted with an artic cooling twin turbo pro on it. My Cpu cooler is the XIGMATEK dark knight.....
Re: Fractal R3
How many slipstreams are you using in your build and what voltages are you running them at? I am choosing between getting the 800rpm slipstream or the 800rpm s-flexes.
My only worry is that 800rpm fans might not be enough to push air through the Fractal R3 case.
My only worry is that 800rpm fans might not be enough to push air through the Fractal R3 case.
Re: Fractal R3
I'm actually using the Sflex not the slipstream. I've only got 2. One on the Cpu and one rear exhaust. They are running at full speed 12V 800 rpm and they are dead silent...
Re: Fractal R3
Love the clean look.
So you replaced the 6870- does the EVGA GTX570 run quietly? Stock cooling by the looks of it?
So you replaced the 6870- does the EVGA GTX570 run quietly? Stock cooling by the looks of it?
Re: Fractal R3
Yes can we have more details about your GPU noise?