Undervolting case fans

Control: management of fans, temp/rpm monitoring via soft/hardware

Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee

Post Reply
JJ
Posts: 233
Joined: Sat Jul 10, 2004 12:24 pm
Location: US

Undervolting case fans

Post by JJ » Fri Mar 02, 2012 2:26 pm

How do you undervolt a case fan that attaches to a three-pin motherboard fan header?

Or, for that matter, one that attaches to a 4-pin Molex connector from the PSU?

Is there any advantage to undervolting, say, a 1200 RPM fan, rather than just using the 800 RPM version of the same model?

Vicotnik
*Lifetime Patron*
Posts: 1831
Joined: Thu Feb 13, 2003 6:53 am
Location: Sweden

Re: Undervolting case fans

Post by Vicotnik » Fri Mar 02, 2012 2:30 pm

Sure. Two main ways to do it, you either lower the voltage or you keep the voltage the same but send it in pulses so that the voltage the fan "sees" is lower (a little bit like +12v, 0v, +12v, 0v really fast). First one is more easy if you want to create your own solution. Most of the time you can have the motherboard do this kind of thing for you. There are also stuff like the Zalman Fanmate that are cheap.

JJ
Posts: 233
Joined: Sat Jul 10, 2004 12:24 pm
Location: US

Re: Undervolting case fans

Post by JJ » Fri Mar 02, 2012 2:48 pm

I haven't bought a motherboard in a number of years. Do the motherboards actually adjust the voltage or do they use PWM? I assume this is configured in the BIOS. Can they be configured to set fans at a fixed speed, because I thought PWM was used primarily for varying fan speed according to some onboard temperature sensor.

If it can't be done through the mobo, apart from fan controllers like the Zalman, does someone sell a (non-adustable) hardware device that you can just plug inline?

Vicotnik
*Lifetime Patron*
Posts: 1831
Joined: Thu Feb 13, 2003 6:53 am
Location: Sweden

Re: Undervolting case fans

Post by Vicotnik » Fri Mar 02, 2012 3:20 pm

How the motherboard controls the fan depends on the motherboard and the BIOS settings. What are you aiming to do, just set the fan to a constant lower speed?
There are inline resistors that you can just plug in, but I would recommend a Fanmate since thats let you set the speed. A bit like a variable resistor.

JJ
Posts: 233
Joined: Sat Jul 10, 2004 12:24 pm
Location: US

Re: Undervolting case fans

Post by JJ » Fri Mar 02, 2012 3:27 pm

Vicotnik wrote:How the motherboard controls the fan depends on the motherboard and the BIOS settings. What are you aiming to do, just set the fan to a constant lower speed?
I was thinking of that, but was mostly just wondering how it was done.

And again, wondering about the reason/advantage of undervolting rather than just using a lower RPM fan.

Vicotnik
*Lifetime Patron*
Posts: 1831
Joined: Thu Feb 13, 2003 6:53 am
Location: Sweden

Re: Undervolting case fans

Post by Vicotnik » Fri Mar 02, 2012 3:36 pm

The obvious advantage is that the fan could spin faster if the need should arise.

ces
Posts: 3395
Joined: Thu Feb 04, 2010 6:06 pm
Location: US

Re: Undervolting case fans

Post by ces » Fri Mar 02, 2012 3:48 pm

JJ wrote:Is there any advantage to undervolting, say, a 1200 RPM fan, rather than just using the 800 RPM version of the same model?
No, other than the flexibility in the future referred to by Vicotnik.

ces
Posts: 3395
Joined: Thu Feb 04, 2010 6:06 pm
Location: US

Re: Undervolting case fans

Post by ces » Fri Mar 02, 2012 3:56 pm

You can pretty much do anything you want with this... and do it in a reproducible manner so you can test and retest different settings in an easily reproducible manner.

2x 12V 3PIN Connector
2x 10V 3PIN Connector
2x 3PIN 8V plug
2x 3PIN 6V plug
2x 3PIN 5V connector
2x 12V 4PIN Molex connectors or
2x 4PIN Molex 5V connector
2x 10V 4PIN Molex connector
2x Molex 4PIN connectors 8V

http://www.performance-pcs.com/catalog/ ... s_id=28783
You do not have the required permissions to view the files attached to this post.

Hasdrubal
Posts: 16
Joined: Wed Feb 22, 2012 8:46 am

Re: Undervolting case fans

Post by Hasdrubal » Tue Mar 06, 2012 12:33 am

ces wrote:You can pretty much do anything you want with this... and do it in a reproducible manner so you can test and retest different settings in an easily reproducible manner.

2x 12V 3PIN Connector
2x 10V 3PIN Connector
2x 3PIN 8V plug
2x 3PIN 6V plug
2x 3PIN 5V connector
2x 12V 4PIN Molex connectors or
2x 4PIN Molex 5V connector
2x 10V 4PIN Molex connector
2x Molex 4PIN connectors 8V

http://www.performance-pcs.com/catalog/ ... s_id=28783
That's quite interesting! I may get one eventually.

Post Reply