It is currently Thu Jul 31, 2014 5:25 pm

All times are UTC - 8 hours




Post new topic Reply to topic  [ 27 posts ] 
Author Message
 Post subject: bulging capacitor still problem?
PostPosted: Sun May 23, 2010 8:59 am 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
The story from several years ago is that there was an industrial espionage by Chinese manufactures of capacitors that missed ingredients that over time caused them to bulge and leak in many famous motherboards and brands like Abit, Asus, Dell, even Apple.

My MSI MSI 975X Platinum V.2 Motherboard Motherboard was made in 2006, unlike Gigabyte ultradurable (which came after I bought MSI) there's no claim of using all-solid Japanese capacitors. I think ASUS also claims Japanese capacitors.

Is it likely an MSI motherboard made in 2006 may have bulging capacitors down the line? Was this issue ever "fixed" by Chinese manufacturers (GB and ASUS goes to great length to claim they get their capacitors all solid from Japanese sources)

How can I tell what kind of capacitor MSI uses in MSI 975X Platinum V.2 Motherboard


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 12:40 pm 
Offline

Joined: Wed Jan 17, 2007 8:10 pm
Posts: 332
Location: Toronto - Ontario - Canada
I wouldn't worry even soild caps bust it's all marketing. My EVGA Geforce 7600 GS bought in 2007 with soild caps did this all the caps burst after it was 11 months out of warranty. Nothing you can do to tell if this happen.


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 1:12 pm 
Offline

Joined: Wed Oct 13, 2004 4:03 pm
Posts: 606
Location: Albany, GA USA
I hope my MB doesn't bust a cap in my ass!


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 1:15 pm 
Offline

Joined: Wed Jan 17, 2007 8:10 pm
Posts: 332
Location: Toronto - Ontario - Canada
Michael Sandstrom wrote:
I hope my MB doesn't bust a cap in my ass!


Don't let you motherboard listen to Rap and it won't.


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 2:30 pm 
Offline

Joined: Sun Oct 09, 2005 8:35 am
Posts: 1253
Location: Pleasanton, CA
Look at the board. If all the power capacitors (the cylinders about 1/4" diameter for the uninitiated) look like metal with a purple D painted on top, they are solid state and likely to outlive the rest of the system. If they look shiny on the top with an indented X then they are electrolytic and subject to failure if they get hot.

How hot is hot? Well, look for a MOSFET (small square chip with three large metal tabs on one side). If you can touch it without YOW! temperature, then your capacitors will last for years. If not, use better cooling, lower CPU voltage, or be prepared to replace your motherboard.

_________________
i7 2600K CPU@4.4 GHz, Asrock Z68, 8GB Corsair Vengeance 1866 CL9, Intel 335 240GB SSD + Samsung HD502HI 500GB, Internal i7 graphics, Antec P180 case, Seasonic X-400 fanless PS, Megahalems CPU HS, Nexus 3-pin & AC PWM fans ~ 600 RPM, AcoustiPack foam, homemade ducts.


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 3:00 pm 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
cmthomson wrote:
Look at the board. If all the power capacitors (the cylinders about 1/4" diameter for the uninitiated) look like metal with a purple D painted on top, they are solid state and likely to outlive the rest of the system. If they look shiny on the top with an indented X then they are electrolytic and subject to failure if they get hot.

How hot is hot? Well, look for a MOSFET (small square chip with three large metal tabs on one side). If you can touch it without YOW! temperature, then your capacitors will last for years. If not, use better cooling, lower CPU voltage, or be prepared to replace your motherboard.


This is useful. I've owned this product since 2007, I am wondering if its capacitors will burst any day now...could you look here,

http://www.newegg.com/Product/ImageGall ... otherboard

http://www.bcchardware.com/index.php?fu ... _photo.php

http://www.bcchardware.com/index.php?se ... _photo.php

http://www.bcchardware.com/index.php?fu ... _photo.php

http://www.bcchardware.com/index.php?fu ... _photo.php

http://www.bcchardware.com/index.php?fu ... _photo.php

http://www.viperlair.com/images/reviews ... p/mobo.jpg

http://www.viperlair.com/images/reviews ... socket.jpg

http://www.viperlair.com/images/reviews ... 5xp/nb.jpg


I think it's electrolytic?


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 3:29 pm 
Offline

Joined: Wed Jan 17, 2007 8:10 pm
Posts: 332
Location: Toronto - Ontario - Canada
He's refering to extreme heat and I highly doubt your running that hot since you've owned the board for 3 year now. If your machine was running that hot other components would have failed long ago. Caps bursting is more related to defective poor quality caps then heat. The caps that where on my video burst as I said before and my system was well cooled inside the Antec Sonata II with two 120mm S-flex fans running. My case wasn't issue of heat but defective caps.


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 4:39 pm 
Offline

Joined: Sun Oct 09, 2005 8:35 am
Posts: 1253
Location: Pleasanton, CA
dan wrote:
I am wondering if its capacitors will burst any day now...could you look here,

http://www.newegg.com/Product/ImageGall ... otherboard

I think it's electrolytic?

Nope. Your board has solid state caps in the VRM (the ones around the CPU socket, which are painted blue on your board). There are lots of other caps on the board that are electrolytic, but they are highly unlikely to fail as they just provide bulk capacitance to various components. The "exploding/bulging" capacitor problem many people report is almost always associated with the capacitors in the VRM circuits that feed the CPU its Vcore (or in the case of a graphics card, the GPU). They fail because they get hot and dry out, then start conducting, then get really hot, then burst. This happens in car sound systems too.

You can stop worrying. :D

JC7: it's not unusual for the VRM of a graphics card to get really hot even though nothing else in the system does...

_________________
i7 2600K CPU@4.4 GHz, Asrock Z68, 8GB Corsair Vengeance 1866 CL9, Intel 335 240GB SSD + Samsung HD502HI 500GB, Internal i7 graphics, Antec P180 case, Seasonic X-400 fanless PS, Megahalems CPU HS, Nexus 3-pin & AC PWM fans ~ 600 RPM, AcoustiPack foam, homemade ducts.


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 5:04 pm 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
re:
cmthomson
johnniecache7

Thanks, with MSI now advertising its Big Bang Trinergy hi-c caps and Gigabyte advertising its Ultra durable 3 "all solid Japanese capacitors" and given I've had my motherboard for 3 years, I'm wondering whether it will mysteriously die soon.

My C2D is 1.8 and NOT overclocked. The hard drive though is 6 years old.

The exploding bursting caps based on inferior Chinese capacitors have gotten a lot of bad publicity. Were the ABIT and Dell motherboards with bursting caps and failure exposed to extreme heat? I understand that at least the Dell/HP ones were NOT overclocked and not tampered with as to create extreme out of spec heat (maybe dust??)



What other components will are prone to failure?


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 6:26 pm 
Offline

Joined: Sun Aug 11, 2002 3:26 pm
Posts: 580
Location: USA (Phoenix, AZ)
At work I've replaced a number of machines and motherboards due to bursting capacitors. Even replacement machines have popped a cap or more after about a year.

So far I've had zero problems with solid capacitors.

_________________
SilverStone SG05, Antec Kuhler H2O 620, Scythe Gentle Typhoon AP-13 120MM, Seasonic X-460, ASRock Z77E-ITX, Intel Xeon E3-1230 V2, Samsung 30nm 1.35V 8GB DDR3 1600 RAM, PowerColor AX7750, Samsung Series 830 256GB SSD, Win 7 Ultimate x64
Link


Top
 Profile  
 
 Post subject:
PostPosted: Sun May 23, 2010 8:40 pm 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
josephclemente wrote:
At work I've replaced a number of machines and motherboards due to bursting capacitors. Even replacement machines have popped a cap or more after about a year.

So far I've had zero problems with solid capacitors.


That's reassuring. So if it's not capacitors, what else causes motherboards to malfunction over time? My MSI is out of warranty. I look at GB Ultradurable and MSI Trinergy with some interest if and when my 3+ year MB malfunctions.


Top
 Profile  
 
 Post subject:
PostPosted: Mon May 24, 2010 11:18 am 
Offline

Joined: Fri Sep 19, 2008 1:39 pm
Posts: 307
Location: Toronto, Canada
Usually you can tell before the capacitor will blow that it starts to swell. If your a handy-type of person, you can even replace the swollen capacitors before it blows damaging the board.

I replaced 3 swollen caps on an old IBM server that was acting up and it worked perfectly thereafter!

_________________
Antec 302-S Project
Solo PC with flipped PSU & Mobo
Basement PC flipped and converted

Image


Top
 Profile  
 
 Post subject:
PostPosted: Mon May 24, 2010 6:29 pm 
Offline
SPCR News Editor

Joined: Thu Feb 10, 2005 11:20 am
Posts: 2173
Location: TN, USA
Some caps bulge on the bottom side (near the solder joint) before they bulge on top. If you really want to talk about caps try going to badcaps.net and you'll find plenty of pics and experts. I hung out there back in the day when the Dell GX270 motherboards were failing left and right.

_________________
.
Please put a country in your profile if you haven't already.
This site is international but I'll assume you are in the US if you don't tell me otherwise.
RAID levels thread http://www.silentpcreview.com/forums/viewtopic.php?p=388987


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Fri Aug 10, 2012 2:36 am 
Offline

Joined: Fri Aug 10, 2012 1:53 am
Posts: 2
Well I can tell you MSI still has this problem at least until 2009.
More than 80% of the MSI motherboeard I soold to customers I sold in 2008 - 2010 has failed at the moment.
Of the ones that still work about 50% has bulging capacitors to.
I can replace capacitors myself, but I am done with MSI forever.


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Mon Aug 13, 2012 4:12 am 
Offline
Moderator

Joined: Mon Dec 09, 2002 7:11 pm
Posts: 7366
Location: Maynard, MA, Eaarth
I make sure to buy motherboards with metal capacitors. Most recently, I used an ASRock and it uses all metal capacitors.

_________________
Sincerely, Neil
http://neilblanchard.blogspot.com/


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Mon Aug 13, 2012 3:02 pm 
Offline

Joined: Sun Aug 11, 2002 3:26 pm
Posts: 580
Location: USA (Phoenix, AZ)
NeilBlanchard wrote:
I make sure to buy motherboards with metal capacitors. Most recently, I used an ASRock and it uses all metal capacitors.


I have mostly been doing the same. Anything without 100% solid capacitors I normally ignore.

However, when doing some builds where I wanted good performance with low idle power consumption, I went with Intel's DH61DL. This motherboard has 11 solid capacitors and 10 regular capacitors. Hopefully Intel is a safe choice...

I am still replacing prebuilt brand name machines at work due to this problem. Often the computers just start operating slower than they should. I'd visually inspect the capacitors one day and they all look fine. Two months later they are bulging.

_________________
SilverStone SG05, Antec Kuhler H2O 620, Scythe Gentle Typhoon AP-13 120MM, Seasonic X-460, ASRock Z77E-ITX, Intel Xeon E3-1230 V2, Samsung 30nm 1.35V 8GB DDR3 1600 RAM, PowerColor AX7750, Samsung Series 830 256GB SSD, Win 7 Ultimate x64
Link


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Mon Aug 13, 2012 7:30 pm 
Offline

Joined: Mon Aug 13, 2012 7:17 pm
Posts: 1
My father had an MSI board (K9A platinum) die recently due to bulging capacitors. I am not 100% sure but I think it was purchased in 2009.
It was exacerbated by an Antec case fan that had died although there was still one working fan in the system. There were several capacitors that were bulging and leaking on the board.
Several were near the VRM and there were a few more toward the memory side.

I'll never buy a board with electrolytic capacitors again.


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Tue Aug 14, 2012 3:13 am 
Offline

Joined: Fri Aug 10, 2012 1:53 am
Posts: 2
I don't think all capacitors with a "soft" top are bad.
Actually, I prefer those capacitors because then you can see earlier when they start failing.
All MSI needs to do (imao) is use better quality ones and/or with a little higher max voltage.
Personally, I have never seen structural problems with these capacitors on motherboards other than MSI.


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Wed Aug 15, 2012 8:04 am 
Offline

Joined: Mon Mar 21, 2005 11:18 am
Posts: 78
Location: Hessle
I have an a Biostar M7NCD from 2004 and MSI K9AG Neo2-Digital from 2007 both with traditional capacitors. Neither, touch wood, are displaying any signs of failure yet.

The Dell Optiplex GX270 (or possibly GX260) towers we had at my old place of work almost all suffered motherboard failure due to leaking capacitors (a couple of them failed twice). Dell always denied there was an inherent problem with the model.


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Thu Sep 06, 2012 6:23 pm 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
Layon wrote:
Well I can tell you MSI still has this problem at least until 2009.
More than 80% of the MSI motherboeard I soold to customers I sold in 2008 - 2010 has failed at the moment.
Of the ones that still work about 50% has bulging capacitors to.
I can replace capacitors myself, but I am done with MSI forever.


uh-oh

i own a msi platinum 975x ver 2 :roll:


Top
 Profile  
 
 Post subject: Re: bulging capacitor still problem?
PostPosted: Thu Sep 06, 2012 6:25 pm 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
what are metal cap and how do I know if MSI or Gigabyte uses them?


Top
 Profile  
 
 Post subject: Re:
PostPosted: Thu Sep 06, 2012 6:27 pm 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
cmthomson wrote:
dan wrote:
I am wondering if its capacitors will burst any day now...could you look here,

http://www.newegg.com/Product/ImageGall ... otherboard

I think it's electrolytic?

Nope. Your board has solid state caps in the VRM (the ones around the CPU socket, which are painted blue on your board). There are lots of other caps on the board that are electrolytic, but they are highly unlikely to fail as they just provide bulk capacitance to various components. The "exploding/bulging" capacitor problem many people report is almost always associated with the capacitors in the VRM circuits that feed the CPU its Vcore (or in the case of a graphics card, the GPU). They fail because they get hot and dry out, then start conducting, then get really hot, then burst. This happens in car sound systems too.

You can stop worrying. :D

JC7: it's not unusual for the VRM of a graphics card to get really hot even though nothing else in the system does...


Layon wrote:
Well I can tell you MSI still has this problem at least until 2009.
More than 80% of the MSI motherboeard I soold to customers I sold in 2008 - 2010 has failed at the moment.
Of the ones that still work about 50% has bulging capacitors to.
I can replace capacitors myself, but I am done with MSI forever.



:!:

I've posted pics of the capacitors from newegg -- is it solid or metal or electrolytic?

thus far my computer seems okay


Top
 Profile  
 
 Post subject: Re: Re:
PostPosted: Fri Sep 07, 2012 12:37 pm 
Offline

Joined: Sun Oct 09, 2005 8:35 am
Posts: 1253
Location: Pleasanton, CA
dan wrote:
I've posted pics of the capacitors from newegg -- is it solid or metal or electrolytic?

Um, where?

On a related topic, it's not only motherboard caps that have issues. The main board in my Samsung 244T display failed because of bulging capacitors. Replacing them (with a kit found online) revived this excellent expensive monitor...

_________________
i7 2600K CPU@4.4 GHz, Asrock Z68, 8GB Corsair Vengeance 1866 CL9, Intel 335 240GB SSD + Samsung HD502HI 500GB, Internal i7 graphics, Antec P180 case, Seasonic X-400 fanless PS, Megahalems CPU HS, Nexus 3-pin & AC PWM fans ~ 600 RPM, AcoustiPack foam, homemade ducts.


Top
 Profile  
 
 Post subject: Re: Re:
PostPosted: Fri Sep 07, 2012 8:19 pm 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
cmthomson wrote:
dan wrote:
I've posted pics of the capacitors from newegg -- is it solid or metal or electrolytic?

Um, where?

On a related topic, it's not only motherboard caps that have issues. The main board in my Samsung 244T display failed because of bulging capacitors. Replacing them (with a kit found online) revived this excellent expensive monitor...


Image

http://www.bcchardware.com/index.php?full=1&set_albumName=MSI975X&id=SATA_Ports&option=com_gallery&Itemid=&include=view_photo.php


Top
 Profile  
 
 Post subject: Re: Re:
PostPosted: Sat Sep 08, 2012 9:56 am 
Offline

Joined: Sun Aug 11, 2002 3:26 pm
Posts: 580
Location: USA (Phoenix, AZ)
dan wrote:


That picture is of standard electrolytic capacitors.

Capacitors can go bad without even showing signs of bulging.

As dhanson865 mentioned earlier, badcaps.net has a lot of information. I have even ordered a kit from them to repair a Shuttle brand computer which is still going strong.

_________________
SilverStone SG05, Antec Kuhler H2O 620, Scythe Gentle Typhoon AP-13 120MM, Seasonic X-460, ASRock Z77E-ITX, Intel Xeon E3-1230 V2, Samsung 30nm 1.35V 8GB DDR3 1600 RAM, PowerColor AX7750, Samsung Series 830 256GB SSD, Win 7 Ultimate x64
Link


Top
 Profile  
 
 Post subject: Re: Re:
PostPosted: Sat Sep 08, 2012 10:25 am 
Offline

Joined: Sun Jan 25, 2004 2:01 am
Posts: 1087
josephclemente wrote:
dan wrote:


That picture is of standard electrolytic capacitors.

Capacitors can go bad without even showing signs of bulging.

As dhanson865 mentioned earlier, badcaps.net has a lot of information. I have even ordered a kit from them to repair a Shuttle brand computer which is still going strong.


oh, but i understand the most important ones feed vcore voltages --


Top
 Profile  
 
 Post subject: Re: Re:
PostPosted: Sat Sep 08, 2012 10:53 am 
Offline

Joined: Sun Oct 09, 2005 8:35 am
Posts: 1253
Location: Pleasanton, CA
dan wrote:
oh, but i understand the most important ones feed vcore voltages --

The caps in that photo are standard electrolytics. But they are around the south bridge, which rarely gets hot.

The most important caps on a motherboard are clustered around the CPU socket. They get hot because the CPU and the VRM that feeds it both get very hot.

_________________
i7 2600K CPU@4.4 GHz, Asrock Z68, 8GB Corsair Vengeance 1866 CL9, Intel 335 240GB SSD + Samsung HD502HI 500GB, Internal i7 graphics, Antec P180 case, Seasonic X-400 fanless PS, Megahalems CPU HS, Nexus 3-pin & AC PWM fans ~ 600 RPM, AcoustiPack foam, homemade ducts.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 27 posts ] 

All times are UTC - 8 hours


Who is online

Users browsing this forum: MSN [Bot] and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group