Zalman 7000AlCu Decouple Mod
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- Posts: 162
- Joined: Fri Nov 28, 2003 8:25 pm
- Location: Randolph, NJ
- Contact:
Zalman 7000AlCu Decouple Mod
In the spirit of this thread..., I have my own mod to decouple the Zalman fan from the heat-sink. I wanted something that was:
1) Relatively cheap
2) No specialized skill
3) Easily "undone."
Note that I performed this mod before mounting the cooler to CPU, so I don't have any before and after analysis to give you. I can say that with the mod, I am not experiencing any of the vibration / noise issues that some others have been experiencing with the stock fan.
Materials I used:
1/4" Sorbothane, 40 ODO
1/8" Sorbothane, 40 ODO
2, 1/2" #2 self-tapping sheet metal screws
2 washers
The "small" screws in the picture are the original fan screws that come with the cooler, they are replaced with longer ones for reasons which will be obvious. For those that don't know, the metal bracket next to the fan is the mounting bracket.
First, I cut the 1/4" sorbothane (which will sit between the fan and the bracket) into stips that match the bracket. I could have just cut one large "square", but I wanted to keep airflow as close to the original design as possible, to minimize any chance of a negative impact on air flow. I also cut two "ghetto washers" out of the 1/8" sorbothane, which will be used to decouple the srew head from the metal bracket:
In order to "push" the screws through the sorbothane, I found it helps to poke a pilot hole completely though the sorbothane with a pin first. Here you can see the screw+metal washer+sorbothane "washer" assembly:
Now just remount the fan using the screw assembly, though the bracket and sorbothane, and self-tapped into the fan:
And that's all she wrote!
1) Relatively cheap
2) No specialized skill
3) Easily "undone."
Note that I performed this mod before mounting the cooler to CPU, so I don't have any before and after analysis to give you. I can say that with the mod, I am not experiencing any of the vibration / noise issues that some others have been experiencing with the stock fan.
Materials I used:
1/4" Sorbothane, 40 ODO
1/8" Sorbothane, 40 ODO
2, 1/2" #2 self-tapping sheet metal screws
2 washers
The "small" screws in the picture are the original fan screws that come with the cooler, they are replaced with longer ones for reasons which will be obvious. For those that don't know, the metal bracket next to the fan is the mounting bracket.
First, I cut the 1/4" sorbothane (which will sit between the fan and the bracket) into stips that match the bracket. I could have just cut one large "square", but I wanted to keep airflow as close to the original design as possible, to minimize any chance of a negative impact on air flow. I also cut two "ghetto washers" out of the 1/8" sorbothane, which will be used to decouple the srew head from the metal bracket:
In order to "push" the screws through the sorbothane, I found it helps to poke a pilot hole completely though the sorbothane with a pin first. Here you can see the screw+metal washer+sorbothane "washer" assembly:
Now just remount the fan using the screw assembly, though the bracket and sorbothane, and self-tapped into the fan:
And that's all she wrote!
-
- Posts: 162
- Joined: Fri Nov 28, 2003 8:25 pm
- Location: Randolph, NJ
- Contact:
Good point....I did not drill out the holes any bigger...but the screws aren't "threaded" through the bracket in the first place. (They just slip through the holes).sven wrote:But one question i have. Are the fan screws touching the metal bracket or are they fully decoupled (bigger hole than original, ..?)
Mine is faster and easier...but yours is cooler.
I decided to try and quiet my 7000 AlCu and being lazy I drilled out the fan mount holes in the bracket slightly and put in rubber grommets so that the fan assembly is decoupled and clear of the bracket. It is about 1-1.5mm higher than the bracket.
It is now significantly quieter and only took me about 10 minutes to do - the hardest part was getting the grommets into the holes, also used a slightly larger self tapper to hold it together
Sort of makes you ask why Zalman did not do something like this in the first place?
It is now significantly quieter and only took me about 10 minutes to do - the hardest part was getting the grommets into the holes, also used a slightly larger self tapper to hold it together
Sort of makes you ask why Zalman did not do something like this in the first place?
I decided to try and quiet my 7000 AlCu and being lazy I drilled out the fan mount holes in the bracket slightly and put in rubber grommets so that the fan assembly is decoupled and clear of the bracket. It is about 1-1.5mm higher than the bracket.
It is now significantly quieter and only took me about 10 minutes to do - the hardest part was getting the grommets into the holes, also used a slightly larger self tapper to hold it together
Sort of makes you ask why Zalman did not do something like this in the first place?
It is now significantly quieter and only took me about 10 minutes to do - the hardest part was getting the grommets into the holes, also used a slightly larger self tapper to hold it together
Sort of makes you ask why Zalman did not do something like this in the first place?
-
- *Lifetime Patron*
- Posts: 1465
- Joined: Sun Mar 09, 2003 12:27 pm
- Location: Reading.England.EU
Another variation on the theme is at SilentHardware/Dirkvader forums. (The second post is an English version of the first one.)
The link Joe DeFuria put in the first post goes to sven's SPCR post linking to his very same Dirkvader post. So, I guess your link is just one fewer steps. FWIW.dukla2000 wrote:Another variation on the theme is at SilentHardware/Dirkvader forums. (The second post is an English version of the first one.)
I also recommend this mod. I tried it myself with material available to me (no Sorbothane here).
I decoupled the fan from the bracket with some neoprene fabric and grommets.
Then I decoupled the bracket from the heatsink base with neoprene again and the bracket screws with grommets.
Very easy to do mod and reduced vibration based noises audibly (at least on my unit).
Thanks for the tip!
I decoupled the fan from the bracket with some neoprene fabric and grommets.
Then I decoupled the bracket from the heatsink base with neoprene again and the bracket screws with grommets.
Very easy to do mod and reduced vibration based noises audibly (at least on my unit).
Thanks for the tip!
Another more elaborate Zalman CNPS-7000 decoupling mod (with images):
http://www.silenthardware.de/forum/inde ... topic=2309
http://www.silenthardware.de/forum/inde ... topic=2309
-
- Posts: 34
- Joined: Wed Oct 22, 2003 7:05 am
Reviving an old thread here but I just tried this mod tonight and I'm very happy with it. Maybe it's my imagination but my 7000-AlCu seems much quieter now. And the great thing about it was that it was very easy to do (no special tools or skills). The only problem for me was tracking down the materials (none of the hardware stores around me had any screws smaller than #6) but found everything I needed at McMaster.
Many thanks to you, Joe, for coming up with this.
I still have plenty of Sorbothane left so I'm trying to figure out other ways I can apply it to components in my machine.
Many thanks to you, Joe, for coming up with this.
I still have plenty of Sorbothane left so I'm trying to figure out other ways I can apply it to components in my machine.
Did this mod today (with some slight variations) and it worked like a charm. Thanks for posting this one, Joe!
Couldn't find #2 self-tapping sheet metal screws anywhere, so I used #3 regular ones and just reversed the direction, then used #3 hex nuts to tighten them---put a small droplet of Locktite on the hex nut to keep vibrations from working them loose. Used rubber mini-washers. The mod works great!
Couldn't find #2 self-tapping sheet metal screws anywhere, so I used #3 regular ones and just reversed the direction, then used #3 hex nuts to tighten them---put a small droplet of Locktite on the hex nut to keep vibrations from working them loose. Used rubber mini-washers. The mod works great!