U2412M at home and office ... both are dead silent without any buzz at any brighness level

Only buzzing when UPS in back up mode (squarewave UPS) , I believe same thing could occur on any monitor with squarewave UPS

Got G360 few days ago and everything ran smooth & quiet. Except, loud coil whine are pretty noticeable when the PC has turned off (still plugged on power outlet) ... It's not a big deal since I run my PC 24/7 at most, but if I could send this unit for RMA, it would be nice Does anyone have same expe...

If you need something more powerfull than Intel GMA, then AMD A6 3500/3600 should work

BTW, are you going to use shader effect for this build?

Stressing single connection with several devices are not a good idea. Over current could fried the main cable/molex connector

By the way, what kind of lights on your setup? is it LED or CCFL?

http://i158.photobucket.com/albums/t116/1kbyte/blog/graf2.jpg At last! Upgrade into larger capacity and mount it on elastic suspension http://i158.photobucket.com/albums/t116/1kbyte/blog/graf4.jpg TMG A3 fan's were removed, left it as passive heatsink http://i158.photobucket.com/albums/t116/1kbyte/...

My first DIY HDD elastic suspension. http://i158.photobucket.com/albums/t116/1kbyte/blog/graf2.jpg http://i158.photobucket.com/albums/t116/1kbyte/blog/graf3.jpg Another rubber band were placed on the rear and front side to prevent slipping http://i158.photobucket.com/albums/t116/1kbyte/blog/graf1.jp...

three weeks at most .... it's quite difficult to keep my computers up in long period since -annoying- power outtage occurs frequently in my country

Currently, I use this rig primarily as download machine with WinXP. Maybe around a couple more week, I would installing Linux then set this rig as proxy server and download machine PROCESSOR : AMD Athlon64 3000+ (Orleans) MEMORY : OCZ Platinum 2GB PC8500@PC5300 MOTHERBOARD : Biostar A780LE HARDISK :...

Silent rig is my first priority and low power consumption is my second concern ... both are my reasons

Silence:Low Power = 55:45

None of Seasonic PSU were designed to run semi-passive except Seasonic X series. Most likely you got a defective unit

nice build! :thumb:
What is the noise & bearing specification of 6cm rear fan? does it came with 3pin?

Bit noisy at low load and more noisy at high load

Noise from ADDA fan on this PSU was so annoying. Mine become much quiter after did some fan swap

CnQ won't work with manual voltage settings(at least on K10). Well, it's not a big matter though
You can overide this problem with custom P-state software (ex:RMClock,PhenomMSRTweaker)

*using X4 620 w/ PhenomMSRTweaker.Currently run 1.1625v@full-load & 0.9750v@idle

Currently using X2 4200+ @2.4GHz 1.050v (default 2.2GHz 1.25v) cooled by passive Deepcool Ice Blade Pro without any problem on my rig

My question -- the ADDA is a 2 wire fan whereas the Scythe is a 3 wire fan... do you just connect the red and black wires and leave the yellow (control?) wire disconnected? Also, how does the psu control the voltage on the fan over just two wires? Thanks in advance. Yellow is a RPM sensor, not a RP...

My Biostar 4670 was burnt 2 month ago, caused by Zalman VNF100. I check throughly on both installation and manual after this "incident" but cannot find anything wrong .... anyone had same experience?

Internal design is similar to PowerColor Eruption.