Drivers for the chipset or what drivers do you mean? Product family Chipsets Product line Embedded Chipsets Product name Intel® NM10 Express Chipset Operating System Windows 7 (64-bit)*(5) http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=20775&ProdId=3304&lang=eng&OSVersion=Windows%207...

Hmm you say it have no 64bit support.

But if you check Intel's spec for the CPU it have "Intel® 64".

http://ark.intel.com/products/58917/

Any chanse to fit a Scythe Big Shuriken in this case??

If you only use the Case fan and no fan on the heatshink??

With a Corsair 400w i did run this with some OC.

Core i7 [email protected]
Asus Maximus II gene
Corair 3x2gb XMS3
2 x Radeon 4770 crossfire
Intel X25-m

That machine did peek at about 330w.

Ok, so i did remove the NB Zotac sign and did move the CPU fan abit closer to the NB and my new temps are after 2h Linpack+Furmark: CPU: 67c GPU: 90c HDD: 37c Can't fit any fans were the 2x80mm fan bay was. Gona watch a bluray movie and se the temps after a movie. this is the exact same setup i'm lo...

Ok, so now i have got my Antec ISK-300 case :) So first atempt is to fit everything with no mods. I did remove the orginial PSU sins i am gona use my picoPSU and i did remove the side fan mount (don't think i need any more fans). Here you can see that some of the top part of the case is touching the...

Did youst see a new Version of the Zotac 9300 board that have some new whanted fetures :) GF9300-G-E (PCB04) has the following differences from earlier PCB versions: DVI is Dual-Link, not Single-Link; S/PDIF header added to board; 3x SATA instead of 2x SATA; CPU/RAM undervoltage now possible (overvo...

Nopp, i still haven't find any Antec ISK-300 in stock

That case is realy hard to find atm :/

Edit:

Now 1x Antec ISk-300 is on the way

Will post some pics ASAP when i get it.

Go for the Big Shuriken, it works geart for me on my ITX htpc.
Cool my E7200 silent and cool

viewtopic.php?t=55204

My "old" computer was built on the Gigabyte p55m-ud4 and i did use a Zerotherm NV120 and have no problems with space betwen it and my GTX 280 in the first PCI-e 16x slot.

Well 72c is imo more than OK after 18h of linpack on a i7 920 (@4200Mhz).
Usually i never se temp over 65c after 6-10h of gaming or 3d cad rendering.

If i remember correct my i7 920 did run with Stock cooler at stock speed at about 75-77c after a few hour on linpack.

Ye if it is rated 220w it's abit to close :/

Think i am gona try the "Chieftec DPS-300AB-9C 300W" can get it for less than 40€ inc shipping.

My old HTPC was with a Antec Fusion and Corsair CX400 and the did work fine, only nois that did come from the case was my 2.5" hdd. It dosen't mather that the CX400 have tons of cabel that you don't need sins the case is "split" in 2 part so it is only the ODD+PSU on the left side. Did use a Scythe ...

I have the chenbro case, the motherboard I got for it is this one: http://www.logicsupply.com/products/ms_9832 It has 4 sata ports, but I added a half-height pci sata board (using the riser http://www.logicsupply.com/products/80h094340 ) to add 2 more ports internally for the 2.5" and the optical d...

If you have observed 220W power draw from the wall and your PSU is 80% efficient (the current standard for good PSU's), then your system was drawing only a maximum of 176W. So that is well within the capacity of Dell DA-2. Uday I did test on a PSU that is 80+ Gold (90%) and at the wall i did show a...

Ye, antec use some special form factor, but the SFX is small enuff to fit insde the case and still enuff room for e decent CPU cooler.

From the back side to the HDD/ODD holder it is about ~120mm and this SFX is 100mm.

And SFX is 125mm wide and the orginial PSU is about 160mm.

So it shud fit easy.

Ye, both the Winmate board and usual PicoPSU is to week, the system take about 180-220w on full load. Gona check out that topic. Edit: These two PSU i have looked at: http://www.be-quiet.net/be-quiet.net/index.php?StoryID=556&websiteLang=en http://www.chieftec.eu/index.php?option=com_content&task=vi...

Sure it can me mATX if you can find a case that is with in these dimensions (w:150 h:300 d:300 mm) and have hot-swop or easy access for 4x3.5" disk, can't fit any bigger case were it's gona stand. Was planing to use the Chenbro ES30068 case. 4x disk for storage and 1 for OS. www.itxdepot.com don't s...

for an i7 alone your going to need more then a 120mm rad. No 1x 120mm is enuff. I am atm building my setup inside a Coolermaster Elit 340. I am testing if i am only gona run 1x120mm rad or 1x240mm rad och both. 1x120mm rad with 2x120mm Nexus@7v in puss-pull config and i am running the CPU @4.2Ghz i...

I did get a hold Antec NSK1300 case but the PSU inside it is broke. So now i am looking for a new PSU that can fit in the same place as the old one or between the motherboard and the front panel of the case. It need to power this setup: Q9300@3.0 Gigabyte G41 motherboard Ati 4850 or 4770 2x3.5" HDD'...

Have totaly missed this thread

Anyone here know where you can buy "Gigabyte GA-6KIEH-RH" in Europe ??

Hi. I am looking for a ITX board that have 5 or more Sata port and 2xGbit lan. Or 4 sata + 1x mini pci-e slot (can use a pci-e SSD for system disk). Neet to be atlest a atom 330 och higher. The motherboard that fills all my need is Gigabyte GA-6KIEH-RH BUT i can't find any shop that sell it inside E...

lucky-dirk-henning wrote:Hi Merlinen,

this is a very nice and interesting post of yours.

Could you perhaps indicate the exact part number of
that low profile Kingston ram you have installed (KTH - ????)?
I can't read it in your picture.

Thank you very much.

It is :
KTH-XW4400C6/1G
1.8V
BKME0850932

So i did get my Big shuriken to day and i have read that it is some problems mounting it on a Zotac 9300 itx board. I am still missing my blu-ray and case for my HTPC :) Setup is: Zotac 9300 C2D E7200 PicoPSU tx150 and so on (se my sign). I am running the fan in 720rpm, and it's realy inaudible. Hi...

I did try and rotate it 90 degres but you can't.
To get this to work you need to mod the chippset cooler, it's not much you need to mod but still.

It is the mounting bits that takes into chippset cooler.

I will, but Antec ISK300 ain't easy to find atm in Sweden

http://www.prisjakt.nu/produkt.php?p=445874

Ghz ain't everything, remember that

Clarkdale onley have ½ the L3 cache than a Lynnfield have + Lynnfield i7 have a much more agresiv turbo mode.

So clock VS clock i am 100% sure Lynnfield is easy gona out preform Clarkdale.

But onley time will tell..

Well depends on what CPU, don't think a Core i7 870 will be "obsolete" in a few month :) And Clarkdale looks more like low-end cpu, same with Arrandale. And Gulftown is realy high-end CPU that is gona start in a price range of 999$+ :shock: Don't see any1 that would replace the new i5/i7 Lynnfield C...

Clarksdale is 2 core and 4 threads with HT.

32nm is "Clarksdale" and as you can see on this chart it is onley for socket 1156.

http://www.guru3d.com/news/intel-core-i ... confirmed/