Where did you get this PWM heatsink? It looks great.

Thanks

Bump, PM me for best offer.

Only Zalman MFC2 left.

Only ATI X800XL and Zalman MFC2 fan controller left.

I have a 7200.11 500GB from newegg. It's very good. It's as quiet as HD501LJ at idle. Seek noise also much better than 7200.10, about the same as HD501LJ. They are fast. 12.5ms seek time, ~87MB average reading speed according to HDTach. They runs very cool, ~29/30C at idle/write in my P180B lower ch...

For Sale: New in box Zalman ZM-MFC2 fan controller. Never opened, still sealed. $50USD shipped in CONUS . http://img232.imageshack.us/img232/1745/zalmanmfc2ib6.th.jpg I accept non-CC Paypal payment from verified PayPal users and will ship to Paypal confirmed addresses. My ebay id: http://myworld.eba...

G0 stepping, VID=1.2250v

Quote from asus faq. These three motherboards have been specially designed to express the importance of temperature management of the memory VRM (Voltage Regulator Module, or often called power circuit), as the cooling of memory VRM are often ignored or unnoticed by many users, though it is the key ...

Asus P5K Dlx system temp also a bit high, around 42C idle. Asus claim: The system temperature sensor has been placed right next to the memory VRM circuit, allowing the motherboard to reflect the rise and fall of memory VRM temperature at real time. In order to lower its temperature, we strongly reco...

Ultra-120 Ex fit P5K-dlx without problem.

kmatheny wrote:My P180B arrived from Newegg today, and it's a 182.

This case is very nice - manufacturing quality is excellent.

Which warehouse did you P180B ship from? Thanks.

Basically, the one with 1.225v default vid should have great oc potential.

You may use Coretemp 0.94 to verify the default vid.

http://www.thecoolest.zerobrains.com/Co ... reTemp.zip

I think you'd better go with dual core cpu for H264 clips.

That's because E6600 have different default VID, one is 1.325v, another is 1.225v.

http://www.jab-tech.com/Thermalright-HR ... -3721.html

Thermalright HR-03 Plus

May I ask, where did you buy your P180B? Thx Hey, you guys talked about some of the improvements of the P180(B) that will be implemented in the upcoming P182. I paid particular attention to that section as I had just bought a P180B (beginning of February) for my first PC build. What struck me as odd...

If you go for a 7600 GT then you should seriously consider the XFX Fatality one - factory overclocked and has a passive cooler + 2yr warranty. review/benchmarks: http://www.guru3d.com/article/Videocards/411/ ps. Just noticed you need an AGP one but I am pretty sure I read in a review that there is ...

The D975XBX cpu fan connector can only control pwm (4 pin) fan. So your nexus runs at full speed all the time.

BillyBuerger wrote:Although, you could just wait another month for the Core 2. It seems this board may have a short lifespan.

The Aopen i975Xa-YDG can support Merom CPU which is mobile Conroe.

The Zalman 7000-AlCu sits very loose due to the lack of IHS. I compensated for it by rolling a little rectangle of electrical tape and putting it under the "V" of the heatsink clip (requires removal of the fan). It works decently, but still not enough pressure IMO. I use Zalman 7000-AlCu, it works ...

MikeC wrote:In case people didn't notice, masumo has a "AMD San Diego 3700+ (OCd to 3.60 GHz)".

I doubt he can OC his SD3700+ to 3.6GHz on Air. 2.6GHz is more realistic.

As title. Did someone swap the fan on Zalman VF-900CU? Looks like the fan mounting system is a little bit different than VF-700CU.

You may try to fix the thermalright HR-05 NB HSF on ASUS MB, and zip tie a 80mm nuxes to the HR-05. Havn't try it but looks it should fit well.

mckennaiii wrote:i picked up a xp90c lapped.
what's the best 92mm fan for this cooler?

Nexus 92mm fan.

The distance of the two hooks on the aopen i975Xa is small. I can't fix the thermailright HR-05 to the NB because the M shape clip is too long.

newegg has it.

http://www.newegg.com/Product/Product.a ... 6811129017

I removed the foam shim from the stock heatsink (come with the mobo) and sticked it on the processor. I mounted my nexus 92mm fan modded zalman 7000A-AlCu on my yonah. Works perfect.

The biggest noise source in my system is the little 40x10mm chipset fan. Even I slowed it to 2500rpm, I can still hear it. :x I tried to replace the stock chipset cooler to thermalright HR-05, but I cannot fix it to the mobo using the M-shaped clip, cause the distance between the two loops is too s...

gogos7 wrote: Can you run the Yonah CPU with your heatsink, but fanless?

I havn't tried to run the CPU fanless. I guess I can. I will try that later.

Thank you.