Twin Turbo Pro Installed on my 5870 :-)
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
Finally got my Twin Turbo Pro installed. It's not silent, but it's a lot better than the stock cooler. I took some pictures of the installation, but will post them later. VRM temperatures under normal game load (Mass Effect 2) are hotter than with the reference cooler, but nowhere close to critical, so you don't need a VRM-3 or VRM-4. You could get one for peace of mind I suppose, but it's more important to have good case flow.
It should be, barely. You have to use the Crossfire connector closest to the back of the case. In addition the card and cooler take up 3 card slots, so there's not a lot of clearance for airflow.mindz wrote:Is this badboy Crossfire compatible? So will it fit 2x 5870 both with twin turbo?
I've posted some pictures here:
http://picasaweb.google.com/frode.aleks ... directlink
My problem now is actually that the power demands for the 5870 has pushed up the load on my Corsair VX550 PSU enough that the fan noise from it is overpowering everything else. Idle is still fine though.
EDIT: One thing I forgot to mention is that the fan speed sensor doesn't work with the TTP - it just goes completely nuts. Thankfully it doesn't affect the voltage of the fan speed controller.
"The cooler fits by bending some 9-10 fins in the corner near the DVI cover, but even then it's a close call."
Where on the picture you posted are the fins you're referring to? I need any help I can get to install this this week.
Thx
ps I found this but translating it to english still leaves me confused:
"If we now want to mount the cooler on a single HD 5850, you will notice that the DVI ports are in your way. It must, however, only a few slats broken parts, so that the cooler fits. This work we have done to us and realized that this is done in a few easy steps. You do not even need this tool. Simply the fan part, which is hooked onto the slats lift, and bend the individual plates and place again, bend over, up until they break. That makes it around 11-12 pieces, then fit the cooler. The fan on it part clip and finished."
Where on the picture you posted are the fins you're referring to? I need any help I can get to install this this week.
Thx
ps I found this but translating it to english still leaves me confused:
"If we now want to mount the cooler on a single HD 5850, you will notice that the DVI ports are in your way. It must, however, only a few slats broken parts, so that the cooler fits. This work we have done to us and realized that this is done in a few easy steps. You do not even need this tool. Simply the fan part, which is hooked onto the slats lift, and bend the individual plates and place again, bend over, up until they break. That makes it around 11-12 pieces, then fit the cooler. The fan on it part clip and finished."
I forgot to mention - there's no point in setting the fan speed to a fixed 40% like falcon26 did. If you just leave it on auto, it'll very slowly ramp from 20% (idle) to 40% max.
In my Antec P182 case with stock fans set to low the max GPU temperature after one hour of OCCT was 87C, and VRM temperatures hit 134C. That may seem high, but no throttling of the GPU clock speed occurred. During normal gaming they hit around 80-90C, with the GPU quite a bit less at around 62C or so. This is just more confirmation that you don't need a VRM-3 or VRM-4. That said, I don't recommend running occt 24/7 - just because it's stable, doesn't mean that it's meant to be run this way, nor that it's not an abnormally high wear on the VRMs.
Case temperature hit a toasty 46C, which is mostly because I'm running with a stock fan setup.
-
Overclocking to 890/1290 using ATI's Auto-Tune increases the gpu temperature to 89C, VRM at 136, fan goes up to 47%, but no problems or throttling occurs.
In my Antec P182 case with stock fans set to low the max GPU temperature after one hour of OCCT was 87C, and VRM temperatures hit 134C. That may seem high, but no throttling of the GPU clock speed occurred. During normal gaming they hit around 80-90C, with the GPU quite a bit less at around 62C or so. This is just more confirmation that you don't need a VRM-3 or VRM-4. That said, I don't recommend running occt 24/7 - just because it's stable, doesn't mean that it's meant to be run this way, nor that it's not an abnormally high wear on the VRMs.
Case temperature hit a toasty 46C, which is mostly because I'm running with a stock fan setup.
-
Overclocking to 890/1290 using ATI's Auto-Tune increases the gpu temperature to 89C, VRM at 136, fan goes up to 47%, but no problems or throttling occurs.
-
- Posts: 67
- Joined: Sun Sep 02, 2007 3:30 am
- Location: www.NEQX.com
- Contact:
temps/fan control?
CCC doesn't seem to adjust the cooler's fan speed even when it's set at auto when I'm benchmarking using 3dmarkvantage..Anyone else have that issue? Only way I'm able to bump up the fan rpm is using the manual fan control..
Screen shot of all my settings and results using furmarkJamieG wrote:Try Furmark - I understand that's the best way to stress test a graphics card. If the card doesn't ramp up, then something may not be right in the card's BIOS or with the fan connection.netjack wrote:i'm using 3dmark vantage that is pushing the temps way up on the card soooo
http://smg.photobucket.com/albums/v510/ ... nt=vid.png
As you can see the card hit between 80-95c and the fan still didn't turn up. If I click on manual control and move the slider up then the fan turns on. So I know it's connected properly but the auto adjustment feature isn't automatically adjusting it. I mean the temps are hot enough under furmark stress to warrant increase in speeds right? It's an xfx brand if that makes any difference.
Thoughts?
In that screenshot the GPU temperature is 47C, and the fan's running at 22% - 20% is the default for idle, so it looks like it's working to me.
What you can try is to use RBE and check if the fan ramps are set correctly:
http://www.techpowerup.com/rbe/
Also make sure that the TTP fans are connected to the video card properly and actually running.
What you can try is to use RBE and check if the fan ramps are set correctly:
http://www.techpowerup.com/rbe/
Also make sure that the TTP fans are connected to the video card properly and actually running.
http://smg.photobucket.com/albums/v510/ ... t=vid2.png
should i lower the tmax to 95? i'm assuming since its set so high, the fan isn't kicking in..
also, once i make the changes, how do i implement them? i get to acquire/flash bios, find winflash on hard drive, hit analyze, then hit flash bios and i get error msg - "Checksum mismatch! Did you select the proper adapter for this bios? can't figure out how to update new bios settings...
should i lower the tmax to 95? i'm assuming since its set so high, the fan isn't kicking in..
also, once i make the changes, how do i implement them? i get to acquire/flash bios, find winflash on hard drive, hit analyze, then hit flash bios and i get error msg - "Checksum mismatch! Did you select the proper adapter for this bios? can't figure out how to update new bios settings...
Actually that looks normal. Once the GPU hits 55C, the fan should slowly start ramping up. Do another furmark test and check GPU-Z to make sure it does. If it doesn't, something is wrong. You'll want to manually set the fan speed in the driver to something appropriately safe, permanently - say 35% or 40%.
Also double-check and make sure you haven't checked the fan control box in CCC.
Also double-check and make sure you haven't checked the fan control box in CCC.
just want to double check that only one of the pwm connectors from the coolers connect to the video board and the other connector just hangs lose not connected to anything, right?
setting it permanently isn't an option because I want to run it deadly silent most of the time (when I'm not playing games) so I have to get this to work...
what about flashing to use the bottom table of steady ramping up?
man i give up, nothing i do causes it to automatically turn on the fans..
I'm using CCC 1211.1547.28237. Is there some other ati-approved program that will kick these fans into high gear when the temps go up? I might have to give AC a call tomorrow..
setting it permanently isn't an option because I want to run it deadly silent most of the time (when I'm not playing games) so I have to get this to work...
what about flashing to use the bottom table of steady ramping up?
man i give up, nothing i do causes it to automatically turn on the fans..
I'm using CCC 1211.1547.28237. Is there some other ati-approved program that will kick these fans into high gear when the temps go up? I might have to give AC a call tomorrow..
Right. I have the four-pin one connected - three pin hangs loose.netjack wrote:just want to double check that only one of the pwm connectors from the coolers connect to the video board and the other connector just hangs lose not connected to anything, right?
Reason I suggested setting the speed permanently, is because the fans really are quite quiet at those speeds.
You can modify the bios like you suggest, but I'd hesitate to recommend it in case something goes wrong.
Your CCC looks old - try Catalyst 10.2, which is the latest. Ati Tray Tools also has a limited fan control option.
Which program has better fan control?flinx wrote:Right. I have the four-pin one connected - three pin hangs loose.netjack wrote:just want to double check that only one of the pwm connectors from the coolers connect to the video board and the other connector just hangs lose not connected to anything, right?
Reason I suggested setting the speed permanently, is because the fans really are quite quiet at those speeds.
You can modify the bios like you suggest, but I'd hesitate to recommend it in case something goes wrong.
Your CCC looks old - try Catalyst 10.2, which is the latest. Ati Tray Tools also has a limited fan control option.
Ati Tray Tools let you set up profiles, so you can have different ones for different situations. CCC is the same as usual - hopefully the newer version makes the fan ramp up properly like it's supposed to. Since manual fan control does work, it's most likely either a driver glitch, or a bios one. You could also try hooking up the reference cooler to the fan header temporarily (make sure you have a table fan or something to help cool the card while testing) to see if that ramps up.
Don't. That temperature is fine, and so is the fan speed. The ramping profile in the bios is set so that you only hit 100% fan speed at 105C gpu core temperature, so you still have quite a bit of headroom. You'll also get a lot lower temperatures during normal gaming. Furmark/OCCT is really only to see how bad something can get in a worst case scenario and make sure there's nothing that becomes unstable under load.netjack wrote:ok got a new cooler and stuck it on and voila it does auto adjust..only prob is CCC never pushes higher than 40 and with furmark, my card is still hitting 90 when all is said and done..how can i get the fan to get up to 90/100%?
On the 5870, you'll have to use 3rd party VRM/RAM sinks - if you look at my pictures you'll notice the stock cooler is part of the base plate and can't be separated from it, unlike the 5850. If the base plate is separable, it's a much better cooler for VRMs and RAM since you get a much larger surface area. The back plate will also help cool since the screws will help distribute heat to it, even though there's no RAM on the back of the card.