How do U make PC start/turn on without going over to it
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
How do U make PC start/turn on without going over to it
--------------------------------------------------------------------------------
I have a shuttle sk43g that I just setup with a hauppauge and firefly remote, that I built as a HTPC. I can shut it down without getting up but how do I turn it on without getting up. It pumps out too much heat to leave it on all the time.
Any ideas?
Thanks
I have a shuttle sk43g that I just setup with a hauppauge and firefly remote, that I built as a HTPC. I can shut it down without getting up but how do I turn it on without getting up. It pumps out too much heat to leave it on all the time.
Any ideas?
Thanks
-
- Posts: 86
- Joined: Fri Feb 25, 2005 8:05 am
- Location: Minnesota
Actually all motherboards maintain that low power line. It is used for things like wake-on lans, but also powering up via USB/PS2 mice/keyboards, as well as the main power switch wich is a contact on the mobo, not the power supply.
However I think you may need a special remote that would support such a feature, like one that emulates a keyboard for the sake of activating wake on keyboard computers.
You can also concievably combine a remote controled POWER switch, and configure your motherboard bios to start up the computer after a power loss.
However I think you may need a special remote that would support such a feature, like one that emulates a keyboard for the sake of activating wake on keyboard computers.
You can also concievably combine a remote controled POWER switch, and configure your motherboard bios to start up the computer after a power loss.
-
- Posts: 580
- Joined: Sun Aug 11, 2002 3:26 pm
- Location: USA (Phoenix, AZ)
Newegg has a remote device, LOGISYS FP800SL or FP800BK which have remote ON/OFF and reset capabilities. A little expensive at $30 plus shipping though...
EDIT: Plus it uses a drive bay which you probably don't have enough room for in a Shuttle... Maybe it can be taken apart to use only it's remote feature?
EDIT: Plus it uses a drive bay which you probably don't have enough room for in a Shuttle... Maybe it can be taken apart to use only it's remote feature?
Wake On USB
I have a question here... I've been experimenting with the various motherboards that I own, because I'm in a similar situation - I have an HTPC (which doesn't support wakeup by anything apparently), and I'd like to learn how this stuff works before I invest in another motherboard (so I know what to look for).
How does Wake On USB work? I know that with Wake On Key (keyboard input) can either wait for a specified key or any key (depending on motherboard support), and Wake On LAN works by waiting for a specified packet, but what requirements are there for Wake On USB?
I tried hooking up an ATI Remote Wonder (a RF USB remote), did a shutdown (under Windows), and while I could use the keyboard to revive the system, the ATI Remote Wonder would not. I also tried Hibernate.
Of course, once I figure this stuff out, I'll have to totally relearn it for Linux, but since I already have Software Suspend2 working, I just need BIOS support. I will likely end up programming a button on my remote to mimic a key on my wireless IR keyboard, and start the system up that way.
-- Joe
How does Wake On USB work? I know that with Wake On Key (keyboard input) can either wait for a specified key or any key (depending on motherboard support), and Wake On LAN works by waiting for a specified packet, but what requirements are there for Wake On USB?
I tried hooking up an ATI Remote Wonder (a RF USB remote), did a shutdown (under Windows), and while I could use the keyboard to revive the system, the ATI Remote Wonder would not. I also tried Hibernate.
Of course, once I figure this stuff out, I'll have to totally relearn it for Linux, but since I already have Software Suspend2 working, I just need BIOS support. I will likely end up programming a button on my remote to mimic a key on my wireless IR keyboard, and start the system up that way.
-- Joe
Re: Wake On USB
How to Enable the Wake from Standby Option for a USB MouseVultureJ wrote: How does Wake On USB work? I know that with Wake On Key (keyboard input) can either wait for a specified key or any key (depending on motherboard support), and Wake On LAN works by waiting for a specified packet, but what requirements are there for Wake On USB?
I haven't tried this yet, but it is on my list of things to do.By default, the Power Management feature of USB mouse devices is turned off. This setting is different from classic PS/2 computer functionality. Therefore, to enable the Wake from standby option, you must manually turn on the Power Management feature for the USB mouse.
To manually enable the Wake from standby option for the USB mouse, start Device Manager, right-click the USB mouse driver, click Properties, and then click to select the Allow this device to wake the system from standby check box.