Zalman 7000A AlCu modded w/ CHROME FAN! (picture!)
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- Posts: 580
- Joined: Sun Aug 11, 2002 3:26 pm
- Location: USA (Phoenix, AZ)
Zalman 7000A AlCu modded w/ CHROME FAN! (picture!)
Now my Zalman 7000A AlCu has a chromed fan. I have previously modded it with a black Panaflo fan as seen here:
http://forums.silentpcreview.com/viewtopic.php?t=10443
I picked up a 92mm Evercool aluminum frame with chromed fan modded for use with my Zalman. This time I mounted it with 1.8mm Stretch Magic instead of screws so it is completely decoupled. I drilled two more holes in the metal plate the fan mounts onto, to string the Stretch Magic through.
See my Stretch Magic thread here:
http://forums.silentpcreview.com/viewtopic.php?t=11674
This Evercool fan is connected to a Zalman Fan Mate at the lowest speed setting. It spins at about 1065 RPM. This fan along with the Stretch Magic is definitely quieter than the previous mod.
Here is the picture!
http://forums.silentpcreview.com/viewtopic.php?t=10443
I picked up a 92mm Evercool aluminum frame with chromed fan modded for use with my Zalman. This time I mounted it with 1.8mm Stretch Magic instead of screws so it is completely decoupled. I drilled two more holes in the metal plate the fan mounts onto, to string the Stretch Magic through.
See my Stretch Magic thread here:
http://forums.silentpcreview.com/viewtopic.php?t=11674
This Evercool fan is connected to a Zalman Fan Mate at the lowest speed setting. It spins at about 1065 RPM. This fan along with the Stretch Magic is definitely quieter than the previous mod.
Here is the picture!
-
- Patron of SPCR
- Posts: 700
- Joined: Thu Mar 13, 2003 2:38 pm
- Location: California, US
- Contact:
-
- Posts: 121
- Joined: Sun Mar 14, 2004 6:59 am
-
- Posts: 580
- Joined: Sun Aug 11, 2002 3:26 pm
- Location: USA (Phoenix, AZ)
Thanks, everyone!
I'm not really sure about the temperature difference, because since removing the original Zalman fan, I have also made a duct on the side of the case. The Zalman pulls air directly from outside. Even though I'm using a much slower fan speed, my temperatures are a lot lower than before.
For the photo, I used my new Canon PowerShot A80. I placed a sheet of printer paper behind the heatsink and photographed it in macro mode (no flash). Everything was on auto mode. The room has three 6500K fluorescent light bulbs which is probably an odd choice for a bedroom, but I like them.
I use Ulead PhotoImpact for further editing. This picture didn't need much work, the camera did a good job by itself. All I did was the Highlight Midtone Shadow function, adjusting only highlight. Then resize, focus, and save as JPG.
There are many other functions I use to enhance photos, but this camera is so much better than my previous one that I don't have to do much. I remember my first digital camera - I had to do so much to make things look good. Everyone has it so much easier these days...
I'm not really sure about the temperature difference, because since removing the original Zalman fan, I have also made a duct on the side of the case. The Zalman pulls air directly from outside. Even though I'm using a much slower fan speed, my temperatures are a lot lower than before.
For the photo, I used my new Canon PowerShot A80. I placed a sheet of printer paper behind the heatsink and photographed it in macro mode (no flash). Everything was on auto mode. The room has three 6500K fluorescent light bulbs which is probably an odd choice for a bedroom, but I like them.
I use Ulead PhotoImpact for further editing. This picture didn't need much work, the camera did a good job by itself. All I did was the Highlight Midtone Shadow function, adjusting only highlight. Then resize, focus, and save as JPG.
There are many other functions I use to enhance photos, but this camera is so much better than my previous one that I don't have to do much. I remember my first digital camera - I had to do so much to make things look good. Everyone has it so much easier these days...
Re: Zalman 7000A AlCu modded w/ CHROME FAN! (picture!)
Can we get a picture of the mounting?josephclemente wrote:I picked up a 92mm Evercool aluminum frame with chromed fan modded for use with my Zalman. This time I mounted it with 1.8mm Stretch Magic instead of screws so it is completely decoupled. I drilled two more holes in the metal plate the fan mounts onto, to string the Stretch Magic through.
And if you don't have numbers on the change the mod made to the temps, how about just telling us what your temps are with the duct and fan mod?
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
His previous mod was with a Panaflo 92mm L1A swap which he said was quieter than the Zalman. And here is claiming the Evercool is quieter than the Panaflo. Might have something to do with the stretch-cord mounting, too???halcyon wrote:I've tried one Evercool "aluminium" fan and it was noisy as hell.
How is your Evercool at minimum voltage compared to the original Zalman fan?
Perhaps modding with Adda Hypro or Panaflo fan motor would make sense? Hm....
-
- Posts: 1283
- Joined: Thu Aug 07, 2003 2:43 pm
- Location: Charlotte, NC, USA
Aphonos: I've used both a Panaflo 92mm L1a and an Evercool on my Thermalright heatsink. There's a reason he said the heatsink is now quieter: The Panaflo blows compared to the Evercool. The sample I had wasn't even quiet at 5v (yes, it defintetly IS the correct Panaflo model). The Evercool gets fairly inaudible around 6-7v. Plus, it moves more air and it looks prettier.
-
- Patron of SPCR
- Posts: 946
- Joined: Sat Sep 06, 2003 9:57 pm
- Location: Berkeley, CA, USA
- Contact:
I'm telling you guys-- Evercool rocks. The 120mm AL fans, of which I now have three, all produce ZERO mechanical noise. They are the quietest 120mm fans I've owned (of enermax, panaflo, sunon, and a bunch of generics.) They run fine for me at <1000rpm @ 5v (Zalman fanmate throttled to minimum).. the only thing I hear is air movement. You can get quieter fans, it's true, but only by virtue of moving even less air-- you probably can't get a better noise/airflow ratio.
I wouldn't be surprised if the 92mm fans shared the same quiet characteristics.
Plus they do look cool but the most important thing, by far, is their complete lack of any mechanical noise.
I wouldn't be surprised if the 92mm fans shared the same quiet characteristics.
Plus they do look cool but the most important thing, by far, is their complete lack of any mechanical noise.
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
Re: Zalman 7000A AlCu modded w/ CHROME FAN! (picture!)
From where? What is the model number?josephclemente wrote:I picked up a 92mm Evercool aluminum frame with chromed fan modded for use with my Zalman. [/img]
Please post pics of your mounting method.
Thanks!
-
- Posts: 580
- Joined: Sun Aug 11, 2002 3:26 pm
- Location: USA (Phoenix, AZ)
The Evercool fans I got were from CompUSA. They were pretty expensive ($15 each!) but I was desperate.
To mount the fan, I first drilled two 1.5mm holes below the fan, just as the stock Zalman fan is drilled. I left the fan in the aluminum frame during this procedure.
Then, I removed the fan from the aluminum frame and snipped off the excess plastic posts with cutting pliers.
The metal fan mounting bracket on the Zalman has two holes for the mounting screws. I decided to use Stretch Magic instead.
I drilled two additional holes (1.5mm) into the base, just opposite of the stock hole locations. This is because I wanted to string the Stretch Magic between the fan and the metal base so the fan won't tilt. The fan isn't "suspended" or hanging, it is merely resting on the material. In addition, the Stretch Magic is strung through the two holes I made on the fan base to keep it all together.
I'm very happy with the results. I like this Stretch Magic stuff.
To mount the fan, I first drilled two 1.5mm holes below the fan, just as the stock Zalman fan is drilled. I left the fan in the aluminum frame during this procedure.
Then, I removed the fan from the aluminum frame and snipped off the excess plastic posts with cutting pliers.
The metal fan mounting bracket on the Zalman has two holes for the mounting screws. I decided to use Stretch Magic instead.
I drilled two additional holes (1.5mm) into the base, just opposite of the stock hole locations. This is because I wanted to string the Stretch Magic between the fan and the metal base so the fan won't tilt. The fan isn't "suspended" or hanging, it is merely resting on the material. In addition, the Stretch Magic is strung through the two holes I made on the fan base to keep it all together.
I'm very happy with the results. I like this Stretch Magic stuff.
For those not familiar with colour temperature, that's a daylight balance, and high noon at that. Typical stage lighting, before moving lights, is 3200K, your home incandescents about 2900K.josephclemente wrote: three 6500K fluorescent light bulbs which is probably an odd choice for a bedroom, but I like them.
-
- Posts: 230
- Joined: Thu Mar 25, 2004 7:11 pm
- Location: Friday Harbor, San Juan Island, WA, USA....Just West of B.F.Egypt
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
-
- Posts: 230
- Joined: Thu Mar 25, 2004 7:11 pm
- Location: Friday Harbor, San Juan Island, WA, USA....Just West of B.F.Egypt
-
- Posts: 580
- Joined: Sun Aug 11, 2002 3:26 pm
- Location: USA (Phoenix, AZ)
This looks like a really cool mod. I'm very happy with my 2 120mm evercool aluminum fans on my case. I am thinking of adding the 92 mm to my zalman7000 alcu heatsink since the stock fan has developed a clicking noise. To clear up some confusion, could you either take the fan off and show a picture of the bottom (sticker side) where you drilled the holes or go here ( http://us.st7.yimg.com/store1.yimg.com/ ... 0_27875021 ) and use mspaint to draw where you drilled/threaded the strech magic. Thanks.