Help choosing fan for TRUE (ultima-90)
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
Help choosing fan for TRUE (ultima-90)
Hello!
I need a new fan for my cpu cooler ultima-90 ,and I need it to be quiet AND as cooling as possible , I've been thinking about :
1.Scythe S-flex 1600rpm
2.Scythe GentleTyphoon AP15
3.Enermax Apollish
4.Scythe SlipStream 1200rpm
5.Arctic Cooling AF12025 PWM
another question : will it help if I install 2 fans on TRUE , one 120mm and another on the other side 90mm fan to take the air out of the TRUE to the rear fan in the case?
oh and are those 5 fans that I mentioned able to lower/increase the RPM according to the cpu temp. ? I don't wanna change the RPM manually =\
Thank you,
Best Regards,
Eli.
I need a new fan for my cpu cooler ultima-90 ,and I need it to be quiet AND as cooling as possible , I've been thinking about :
1.Scythe S-flex 1600rpm
2.Scythe GentleTyphoon AP15
3.Enermax Apollish
4.Scythe SlipStream 1200rpm
5.Arctic Cooling AF12025 PWM
another question : will it help if I install 2 fans on TRUE , one 120mm and another on the other side 90mm fan to take the air out of the TRUE to the rear fan in the case?
oh and are those 5 fans that I mentioned able to lower/increase the RPM according to the cpu temp. ? I don't wanna change the RPM manually =\
Thank you,
Best Regards,
Eli.
Re: Help choosing fan for TRUE (ultima-90)
To do that the fan needs to be PWM (4 pin). Only the AC fan of those you mentioned is PWM.eliil1 wrote:oh and are those 5 fans that I mentioned able to lower/increase the RPM according to the cpu temp. ? I don't wanna change the RPM manually =\
Since your CPU Cooler isn't designed to perform as good as posible with a low rpm quiet fan (due to the lower fin distance), you will need a fan that has good static pressure to push enough air through the dense fins. Since you want something silent and with PWM I would recommend you Akasa Apache.eliil1 wrote:another question : will it help if I install 2 fans on TRUE , one 120mm and another on the other side 90mm fan to take the air out of the TRUE to the rear fan in the case?
Using a second fan to pull the air from the cooler's fins won't make any significant difference. If you put another Akasa fan in pull mode you will probably see a decrease of temperature by 2-3 degrees celcius.
Will Arctic Cooling AF12025 PWM do the job? or even 2 fans like this?
I can't find the Akasa in my city...
Only :
1. GentleTyphoon A14
2. AC AF12025
3. Apollish
4. ZM-F3
5. Slipstream 1200rpm
which one has the best static pressure? and which one will drop the temps the most ?
about the RPM speed, can I set in bios that at particular temps the RPM will increase and etc.? or only if it's PWM ?
(the cooler is Ultima-90, I got confused at the beginning I thought it's TRUE...)
thank you,
I can't find the Akasa in my city...
Only :
1. GentleTyphoon A14
2. AC AF12025
3. Apollish
4. ZM-F3
5. Slipstream 1200rpm
which one has the best static pressure? and which one will drop the temps the most ?
about the RPM speed, can I set in bios that at particular temps the RPM will increase and etc.? or only if it's PWM ?
(the cooler is Ultima-90, I got confused at the beginning I thought it's TRUE...)
thank you,
Re: Help choosing fan for TRUE (ultima-90)
I have the S-Flex 1600RPM cooling my Thermolab Baram, connected directly to the Gigabyte EP45-UD3P's CPU fan header. It's running below 800RPM at idle (BIOS, HWMonitor). I just set fan control type in BIOS as "voltage" instead of "PWM". Maximum temperature at stock speed (1.26V) is 56C (28C ambient) while running an hour LinX session. PWM may be needed if your motherboard doesn't support fan voltage control. I didn't go for a PWM fan because they're more expensive than their normal counterparts around here.Kimi wrote:To do that the fan needs to be PWM (4 pin). Only the AC fan of those you mentioned is PWM.eliil1 wrote:oh and are those 5 fans that I mentioned able to lower/increase the RPM according to the cpu temp. ? I don't wanna change the RPM manually =\
Like Kimi said, you'd want high static pressure for heatsink fans (S-Flex, GentleTyphoon) and high CFM for case fans (SlipStream).
You better check if your motherboard can undervolt the CPU fan. If it can't and since you don't want to use a fan controller, you're better off with a slower fan or that AC PWM fan. Slower S-Flex or the 1450RPM GT should be good for non-PWM fans.eliil1 wrote:I just checked, in my city I can get only the GT 1450rpm , not 1800rpm. but it's bad isn't it?
I can also find in our stores slipstream 1200 rpm, and Arctic Cooling AF12025 PWM.
which one is better?
I need mostly silence, cooling is very important too tough [=
if there's need , I'll take 2 fans.
I wouldn't use the SS due to its low static pressure. Use it only as a case fan.
Push-pull shouldn't be necessary unless you're overclocking and feeding the CPU a lot of voltage. Better use the pulling fan as a case exhaust instead.
Does your S-Flex spin slower than 800RPM when idle?lm wrote:You don't specify what your TRUE needs to cool, but my TRUE has a Scythe S-FLEX 800rpm fan on it and cools a Q9450. Never bothered to tweak anything in this combo and haven't got any problems with it.
OP's cooler is a TR Ultima-90, not TRUE. More like Mini TRUE.
-
- Posts: 27
- Joined: Mon Jul 06, 2009 2:37 pm
- Location: Texas
I have a couple of the Arctic Cooling 12025 PWMs, and I don't care for them. They don't push much air at a full 12V and have a "propeller" noise character to them, about as loud as my S-Flex SFF21E is at its full RPM (and, subjectively, about twice the airflow). They also won't give an RPM signal back to my fan controller.
I bought these because they were PWM, and because they had fluid bearings. But I probably won't be using them in my PWM application (which I just found out this evening I don't really need PWM for).
I like my Noctua PWM fan that came with the NH-C12P CPU cooler, but alone they are quite expensive -- about twice what a Scythe S-Flex costs.
I bought these because they were PWM, and because they had fluid bearings. But I probably won't be using them in my PWM application (which I just found out this evening I don't really need PWM for).
I like my Noctua PWM fan that came with the NH-C12P CPU cooler, but alone they are quite expensive -- about twice what a Scythe S-Flex costs.