Drive Fan Off when Drives are in standby?

Control: management of fans, temp/rpm monitoring via soft/hardware

Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee

Post Reply
signal64
Posts: 61
Joined: Sun Apr 09, 2006 4:11 am

Drive Fan Off when Drives are in standby?

Post by signal64 » Sun Oct 29, 2006 5:09 pm

I have a few cases with a fan in front of the hard drives and in some cases, I'm using this item from Scythe:

http://www.newegg.com/Product/Product.a ... 6835185020

System is already pretty low wattage, so I tend to just put the hard drives in standby when not in use.

I'd like the fan for the drives to be either on or off depending on the drive status.

Any ideas on the best way to do this?

sciberpunkt
Posts: 14
Joined: Tue Oct 24, 2006 5:42 pm

Post by sciberpunkt » Sun Oct 29, 2006 7:30 pm

Maybe a thermal sensor attached to surface of the HD case that cycles a fan when heat is detected?

signal64
Posts: 61
Joined: Sun Apr 09, 2006 4:11 am

Post by signal64 » Sun Oct 29, 2006 9:26 pm

Good idea.

Haven't seen an on/off type of thermal control though (but will look). The majority seems to allow some voltage through (ala FanMate or Thermistor on the fan itself) and don't have a temp threshold. Might have to build something.

Maybe more complicated, but had an idea that could handle a couple of other situations.

Was thinking of a Sunbeam Theta and use SpeedFan to control it. Not sure how well the Theta works with SpeedFan and looking into that as well.

pyogenes
Posts: 273
Joined: Wed Oct 11, 2006 10:38 am
Location: Chicago

Post by pyogenes » Sun Oct 29, 2006 9:39 pm

if your drives use SMART technology you can set up Speedfan to do what you want assuming you can control fans hooked up to your MB with speedfan.

Have one of your fans tied to the hard drive temp. Set the minimum fanspeed to 0% and the maximum to whatever you want. Set the target temperture higher than the idle temps and you're set.
Joe

signal64
Posts: 61
Joined: Sun Apr 09, 2006 4:11 am

Post by signal64 » Sun Oct 29, 2006 11:12 pm

That's the problem. The motherboard (A8N VM CSM) only allows the CPU fan header to be controlled.

The one other fan header doesn't allow control via speedfan.

Hence, I'd like to try and tie in the motherboard/S.M.A.R.T temperatures to an external fan controller as an overall soltion.

Otherwise the on/off thermal sensor looks to be the simplest (if I can find one).

sciberpunkt
Posts: 14
Joined: Tue Oct 24, 2006 5:42 pm

Post by sciberpunkt » Fri Nov 03, 2006 6:12 pm

My Asus AN8's uGuru fan control in the BIOS setup is something all MBs should have. Voltage range adjustments dependant on temperature delta, user definable with 6 independently controlled fan headers.

I don't know of any motherboard BIOS that accesses SMART or GPU temps directly to control fan speed. Seems obvious though.

signal64
Posts: 61
Joined: Sun Apr 09, 2006 4:11 am

Post by signal64 » Sat Nov 04, 2006 12:37 am

It seems on the uATX boards (which the ASUS A8N VM CSM is) they back off on these features (and sometimes quality) automatically assuming it isn't for the enthusist market.

This is something I found in common with MSI, Abit, and ASUS.

Bluefront
*Lifetime Patron*
Posts: 5316
Joined: Sat Jan 18, 2003 2:19 pm
Location: St Louis (county) Missouri USA

Post by Bluefront » Sat Nov 04, 2006 2:52 am

You can do this procedure easily using a DigitalDoc5 fan controller. You attach one of the eight sensors to the side of the hard drive. You attach the fan to that channel. Then you adjust the turn on point to slightly above the hard drive idle temp. Every time the drive gets above that temp the fan will turn on.
[size=75]"At the core of liberalism is the spoiled child - miserable, as all spoiled children are, unsatisfied, demanding, ill disciplined, despotic, and useless. Liberalism is the philosophy of sniveling brats." - P.J. O'Rourke[/size]

Post Reply