Splitting the rpm signal? Success...
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- *Lifetime Patron*
- Posts: 5316
- Joined: Sat Jan 18, 2003 2:19 pm
- Location: St Louis (county) Missouri USA
Splitting the rpm signal? Success...
I'm controlling two fans with an external LCD fan control....Is it possible to tap into the signal wire (yellow) from the fans, and plug it into the MB......so the motherboard can also read the rpm signal?
Last edited by Bluefront on Wed Nov 10, 2004 4:25 pm, edited 1 time in total.
IIRC, the Tach line works as a voltage collector circuit. If you want to see the fan pulses on an oscilliscope, you would put a 10k resistor or so between the tach line and your voltage line (12V or whatever you're regulating it to), and then hook up your probes to the Fan tach and ground circuit.
Now generally, it shouldn't make a difference if you split the signal. You may have more resistance, but you should still have the same number of pulses.
Now generally, it shouldn't make a difference if you split the signal. You may have more resistance, but you should still have the same number of pulses.
-
- Posts: 1283
- Joined: Wed Sep 03, 2003 1:35 am
- Location: Sweden, Linkoping
The problem I think that you are getting with the temp controlled fan is that the voltage that comes out from the fan to the tach line could be too low to register as high level by the motherboard.
The best way to go here would be to measure the tach signal with a scope and see what comes out. If you are getting a tach signal but it is too low voltage, then it might work to add some bias to the signal.
Perhaps someone with more electronics know-how can help out here? Fancontrol? Cpemma?
The best way to go here would be to measure the tach signal with a scope and see what comes out. If you are getting a tach signal but it is too low voltage, then it might work to add some bias to the signal.
Perhaps someone with more electronics know-how can help out here? Fancontrol? Cpemma?
-
- *Lifetime Patron*
- Posts: 5316
- Joined: Sat Jan 18, 2003 2:19 pm
- Location: St Louis (county) Missouri USA
Well I had to try it....success. Both the fan controller and Speedfan now read RPMs. And the readings seem to be accurate. The Fan controller reads down to the 100's and Speedfan down to the 10's.....which was the reason for this mod. I wanted a more accurate idea of rpms, plus the controller wouldn't read below 1000rpms. Speed fan seems to be accurate and stable down to the fan's slowest speed...850rpms.
Will it work for you....try it to see.
BTW....I only used the yellow signal wire to the board.
Will it work for you....try it to see.
BTW....I only used the yellow signal wire to the board.
-
- Posts: 380
- Joined: Thu Jul 15, 2004 12:44 pm
- Location: UK
Hah, brilliant - I was thinking of doing exactly this when I build my new system. Glad you jumped the gun and guineapigged for me!
One question; how did you connect the split yellow to the board header? Do you have spare plugs? Or does your fan controller use molex connections instead of the 3-pin fan plugs?
The controller I'm getting uses the 3-pins so I guess I'd need spares from somewhere. It's a bit of a pain, but I wanted this one specifically as it doesn't use PWM.
One question; how did you connect the split yellow to the board header? Do you have spare plugs? Or does your fan controller use molex connections instead of the 3-pin fan plugs?
The controller I'm getting uses the 3-pins so I guess I'd need spares from somewhere. It's a bit of a pain, but I wanted this one specifically as it doesn't use PWM.
Bluefront, I know you've already tried this and found out it worked, but just to set possibly worried minds of other readers at ease: both my Sunbeam Rheobus and (retired) Coolermaster Aero7 cpu cooler came with a splitter to do just this... so my guess is if they're selling it, it'll probably be safe. At some point you will hit the limit below which the mobo won't read anything of course, but that depends on the board.