HDD Elastic Suspension... Show your pics!
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
Yes, in any Computer shop, at least here in my Country... It cost around 1,2 $ here. (same in €)Volkswagen wrote:
Were can i buy a pair of these in the us ?
I think I will buy an other, to suspend the other Samsung. But my ultimate goal is to have one, quieter HDD in the future with bigger storage capacity (or the same as now, between 200 and 250 Gb).
BR!
Front:
Back:
Two drives supsended in the 5.25" bay of an Antec 3000b.
One is Western Digital Raptor 74gb, the other is a Hitachi 250GB.
The Raptor runs at about 40 C without active cooling.
I can't get readings from the Hitachi but it feels slightly cooler than the Raptor.
This elastic fits in the back groove of the hard drives (see back.jpg) &
hold's the drives fairly securely when moving the case.
It is 1/4" Woven Elastic from JoAnn's; woven elastic maintains its width when stretched. You can buy it by the yard at JoAnn's .
Back:
Two drives supsended in the 5.25" bay of an Antec 3000b.
One is Western Digital Raptor 74gb, the other is a Hitachi 250GB.
The Raptor runs at about 40 C without active cooling.
I can't get readings from the Hitachi but it feels slightly cooler than the Raptor.
This elastic fits in the back groove of the hard drives (see back.jpg) &
hold's the drives fairly securely when moving the case.
It is 1/4" Woven Elastic from JoAnn's; woven elastic maintains its width when stretched. You can buy it by the yard at JoAnn's .
Last edited by omgy on Sat Apr 01, 2006 6:42 pm, edited 3 times in total.
Ok, here's my ghetto suspension.
My 160gb samsung in DiskTwin. Screws are touching the rubber of DiskTwins. I'm using those wires that are found in almost every cable package, they are used to keep the cables nice and tight, everyone should have tons of them. I used short white ones on the rear and longer black wires in the front. The HDD would stay in place even if one of the wires would fail. Or even if both from the rear would fail, the power cord and ide cable would prevent it from falling to the bottom of the case.
Not exactly beautiful solution, but it was pretty swift installation and the samsung is pretty quiet to begin with.
Bottom nexus fan @ 900rpm (9V? It's fan mated, I have no idea of the voltage) is the only intake air in my system, there aren't any holes in the case except for the bottom intake and PSU exhaust. It's enough to keep the Samsung at 30-32c.
I am pretty satisfied to the silencing effect. During normal usage I don't hear the seeks and during night the drive is idle and quiet. I keep my computer on 24/7 and sleep with my head less then 2 meters away from the front of the case.
I'm going to use the same suspension for my upcoming raptor 150gb, when I retire this samsung from active duty and reassign it to be a non active drive image backup.
When I find out that the PSU of breeze isn't able to handle the heat of the system, I will probably just buy P150 or some other case that has soft mounting as a feature at that point. Hopefully there will be a small case with only two 5.25" slots, and two soft mount slots. Even that would be more then I or a big number of users would ever need. Ok, I think I went enough off topic...
My 160gb samsung in DiskTwin. Screws are touching the rubber of DiskTwins. I'm using those wires that are found in almost every cable package, they are used to keep the cables nice and tight, everyone should have tons of them. I used short white ones on the rear and longer black wires in the front. The HDD would stay in place even if one of the wires would fail. Or even if both from the rear would fail, the power cord and ide cable would prevent it from falling to the bottom of the case.
Not exactly beautiful solution, but it was pretty swift installation and the samsung is pretty quiet to begin with.
Bottom nexus fan @ 900rpm (9V? It's fan mated, I have no idea of the voltage) is the only intake air in my system, there aren't any holes in the case except for the bottom intake and PSU exhaust. It's enough to keep the Samsung at 30-32c.
I am pretty satisfied to the silencing effect. During normal usage I don't hear the seeks and during night the drive is idle and quiet. I keep my computer on 24/7 and sleep with my head less then 2 meters away from the front of the case.
I'm going to use the same suspension for my upcoming raptor 150gb, when I retire this samsung from active duty and reassign it to be a non active drive image backup.
When I find out that the PSU of breeze isn't able to handle the heat of the system, I will probably just buy P150 or some other case that has soft mounting as a feature at that point. Hopefully there will be a small case with only two 5.25" slots, and two soft mount slots. Even that would be more then I or a big number of users would ever need. Ok, I think I went enough off topic...
I wondered about that as well, but it seems the heatpipe is of so soft material that it does not transfer vibrations. The drives became really silent after I did that modification.El Doug wrote:nifty - does the vibration pass along the heatpipe at all? i assume the case wall it's attached to does not, considering its thickness
Pate
The Arctic Cooling SIlentium series offers a very nice harddisc-silencer, but only for one drive. If you want to use a second drive in the case you have to mount the drive pretty un-isolated in a 3.5' bay.
Hereby a way to add isolation to that second drive too:
Rubber strips to be mounted on harddrive
Rubber strips stuck to harddrive
Harddrive with rubberstrips mounted in lower 3.5' silentium bay with elastic and zip-tie
after this operation the slight hum was gone.
Hereby a way to add isolation to that second drive too:
Rubber strips to be mounted on harddrive
Rubber strips stuck to harddrive
Harddrive with rubberstrips mounted in lower 3.5' silentium bay with elastic and zip-tie
after this operation the slight hum was gone.
Last edited by sanse on Sat Feb 18, 2006 8:31 am, edited 1 time in total.
hi there!
i have a few questions
i have a Sonata 2 case.
i've put my hard disk on the lower part of the case, i used 3 long rubber bands in my case AND i used a bath sponge under it, with a layer of "wrapping foam" on top of it just in case.
the 3 rubber bands support the hard-disk and touch that layer of "wrapping foam" under it. i placed a bath sponge under it in case the rubber bands crumble so the hard disk will not fall, it'll land on that thick "sponge-and-foam" piece.
my questions now:
-it is safe to put a hard disk directly on a bath sponge?
-if not, is it safer the way i've done it? (bath sponge, thin layer of foam on top, plus 3 bands of rubber touching that foam)
i have a few questions
i have a Sonata 2 case.
i've put my hard disk on the lower part of the case, i used 3 long rubber bands in my case AND i used a bath sponge under it, with a layer of "wrapping foam" on top of it just in case.
the 3 rubber bands support the hard-disk and touch that layer of "wrapping foam" under it. i placed a bath sponge under it in case the rubber bands crumble so the hard disk will not fall, it'll land on that thick "sponge-and-foam" piece.
my questions now:
-it is safe to put a hard disk directly on a bath sponge?
-if not, is it safer the way i've done it? (bath sponge, thin layer of foam on top, plus 3 bands of rubber touching that foam)
thanks for the answerTibors wrote:The computer I am posting this with now has been running for about a year. All this time the HD has been lying on a synthetic carwash sponge.RaptorZX3 wrote:-it is safe to put a hard disk directly on a bath sponge?
so can i take off that layer of foam on top of the sponge?
-
- Posts: 29
- Joined: Tue Nov 08, 2005 10:57 am
- Location: Netherlands Folding for SPCR
feel free, I can't see how a sponge is going to guide heat, so it's not like it's going to warm up. don't worry about electrical conduitivity.
btw if you are so troubled with your hard drive might falling, if you put it on the foam, is there a mechanism that constraints the drive to the foam, i.e. won't it fall sideways (in transport)
btw if you are so troubled with your hard drive might falling, if you put it on the foam, is there a mechanism that constraints the drive to the foam, i.e. won't it fall sideways (in transport)
i don't plan in transporting this computer anyway...
i replaced regular rubber bands by clothing elastics, nearly 1 inch wide.
but my Sonata 2 case i have is a bit tricky, you have to use the lower compartment so you can put an elastic and push it more inside the case to support the front weight of the hard disk, to be sure the weight of it or the vibrations won't push it in a lower angle and eventually fall...i had to use the side hole where you usually pass the front case cables there.
i used 3 pieces of elastics, 2 main ones to support and 1 at the deepest of the case to support that front weight of the hard disk. should i put more? should i use this "criss-cross" technique so many peoples on this forum use?
tell me, anyone have a Western Digital WD2000JS (200gb SATA drive, 7,200rpm) and have/had vibrations problems with it?
i replaced regular rubber bands by clothing elastics, nearly 1 inch wide.
but my Sonata 2 case i have is a bit tricky, you have to use the lower compartment so you can put an elastic and push it more inside the case to support the front weight of the hard disk, to be sure the weight of it or the vibrations won't push it in a lower angle and eventually fall...i had to use the side hole where you usually pass the front case cables there.
i used 3 pieces of elastics, 2 main ones to support and 1 at the deepest of the case to support that front weight of the hard disk. should i put more? should i use this "criss-cross" technique so many peoples on this forum use?
tell me, anyone have a Western Digital WD2000JS (200gb SATA drive, 7,200rpm) and have/had vibrations problems with it?
Wow, nice suspension there!
I have been thinking to buy only one HDD (P80 Nidec Samsung) Instead of the two.
My thermal readings are 44 and 46 C for the two drives...
BR!
I have been thinking to buy only one HDD (P80 Nidec Samsung) Instead of the two.
My thermal readings are 44 and 46 C for the two drives...
BR!
omgy wrote:Front:
Two drives supsended in the 5.25" bay of an Antec 3000b.
One is Western Digital Raptor 74gb, the other is a Hitachi 250GB.
The Raptor runs at about 40 C without active cooling.
I can't get readings from the Hitachi but it feels slightly cooler than the Raptor.
This elastic fits in the back groove of the hard drives (see back.jpg) &
hold's the drives fairly securely when moving the case.
It is 1/4" Woven Elastic from JoAnn's; woven elastic maintains its width when stretched. You can buy it by the yard at JoAnn's .
i tried another way today, by using the clothing elastics to hold the hard disk in place on the big bath sponge, but i could hear the hard disk whine more than before, so i turned back to the clothing elastics suspensions only, with the big piece of bath foam at the bottom (at around half-centimeter of the hard disk, just in case it fall someday, it would land on this instead of landing on a hard metal surface of the case).
goddammit i wish i could live in a more noisy environment so i wouldn't worry that much for a silent computer...
my computer store are such a__holes, they don't even have silencing stuff in stock like this AcoustiPack thing or other things to make computers more silent, like those great and silent Nexus fans...
goddammit i wish i could live in a more noisy environment so i wouldn't worry that much for a silent computer...
my computer store are such a__holes, they don't even have silencing stuff in stock like this AcoustiPack thing or other things to make computers more silent, like those great and silent Nexus fans...
This is my first shot at suspending the spinning things.
Nothing special... just used some elastic for underwear
Here's the end result:
I joined the elastic cord with stitches lol
Although it's a bit of a pain taking the drives out, it's certainly made things a lot quieter than before and I might use some proper elastic cord in the future instead of the stretchy thing found in underwear.
Nothing special... just used some elastic for underwear
Here's the end result:
I joined the elastic cord with stitches lol
Although it's a bit of a pain taking the drives out, it's certainly made things a lot quieter than before and I might use some proper elastic cord in the future instead of the stretchy thing found in underwear.
-
- Posts: 26
- Joined: Tue Jun 29, 2004 1:07 pm
Aluprofiles and "spikes"
My first attempt on this topic was using L-shaped aluminum brackets with drilled holes for hanging in a selfmade cage in elastic ribbons.
After getting a 250 gb Samsung spinpoint I tried to place it, with the L-profiles on the bottom foam pad. It was very silent (and cool) but vibrated a bit, I thought, so I made 4 "spikes":
http://www.badongo.net/pic/156445
Much easier to fit than elastics and working very well (at least if you´ve only got one Hd). Temps are 10C above ambient.
http://www.badongo.net/pic/156430
After getting a 250 gb Samsung spinpoint I tried to place it, with the L-profiles on the bottom foam pad. It was very silent (and cool) but vibrated a bit, I thought, so I made 4 "spikes":
http://www.badongo.net/pic/156445
Much easier to fit than elastics and working very well (at least if you´ve only got one Hd). Temps are 10C above ambient.
http://www.badongo.net/pic/156430
-
- Posts: 5
- Joined: Thu Mar 23, 2006 11:48 am
Cheapness
My no cost solution. Raised above the Zalman intake fan for some airflow.
I am SO amazed at the noise levels of my Samsun HD160JJ hard drive. I used to have a WD 80gb and that thing (after a few years of use) roared!
--------------------------------------
AMD Sempron 3000+, ASrock K8NF4g-Sata2, Samsung 160gb SATAII, Artic Cooling Silencer 64 UltraTC, Corsair Valueselect 1x1gb CL3, Nexus 120mm rear exhaust fan, Zalman 90mm front intake fan, Seasonic SS300-FT psu
I am SO amazed at the noise levels of my Samsun HD160JJ hard drive. I used to have a WD 80gb and that thing (after a few years of use) roared!
--------------------------------------
AMD Sempron 3000+, ASrock K8NF4g-Sata2, Samsung 160gb SATAII, Artic Cooling Silencer 64 UltraTC, Corsair Valueselect 1x1gb CL3, Nexus 120mm rear exhaust fan, Zalman 90mm front intake fan, Seasonic SS300-FT psu
-
- Posts: 15
- Joined: Wed Apr 19, 2006 5:03 am
Here's the suspension from my new HTPC.
I'm using the 1/8" round elastic, and I've come up with what I believe is a new way to attach the drives. It uses heat-shrink tubing to attach regular HD mounting screws to the ends of the elastic. Pic=1000 words.
This seems more elegant and more secure than other methods I've seen, although it is a lot more difficult to remove / replace the drives.
I thought the drive bay cover would be a noise leak so I lined it with a small piece of Acoustipack.
DE
I'm using the 1/8" round elastic, and I've come up with what I believe is a new way to attach the drives. It uses heat-shrink tubing to attach regular HD mounting screws to the ends of the elastic. Pic=1000 words.
This seems more elegant and more secure than other methods I've seen, although it is a lot more difficult to remove / replace the drives.
I thought the drive bay cover would be a noise leak so I lined it with a small piece of Acoustipack.
DE
-
- *Lifetime Patron*
- Posts: 288
- Joined: Sat Oct 22, 2005 10:39 am
Here is my first HD suspension 3.5" HD in the 5.25" Bay under my CD drive Simply in some elastic and a 2.5" HD in the floppy drive bay with some foam to keep it from the sides.
If your wondering why I have bothered with a laptop HD in the same case as a desktop one its because ive been planning on getting a fileserver up and running for a while but since im out of work my funds are rather low at the moment.
If your wondering why I have bothered with a laptop HD in the same case as a desktop one its because ive been planning on getting a fileserver up and running for a while but since im out of work my funds are rather low at the moment.
-
- Posts: 436
- Joined: Fri Feb 17, 2006 8:15 pm
- Location: Michigan
my version...
Thanks to you guys my pc now is much more silent. And here is what i've done with my three seagate harddisc drives:
Version 1:
Version 2: I used bigger foam cutouts and the weight of the drives is now better distributed.
Flickr photoset
The green stuff i cut out of a nice soft camping mattress and it decouples quite well and as a side benefit dampens the "swinging around". The 5 1/4'' cage in the front bottom is for the (overpriced) silentmaxx hdd silencers, since this is a noise-insulated case by that manufacturer. They do recommend adding a fan if you use them, by the way. The fan in the bottom is regulated by electronic, decoupled and nearly inaudible, too.
Version 1:
Version 2: I used bigger foam cutouts and the weight of the drives is now better distributed.
Flickr photoset
The green stuff i cut out of a nice soft camping mattress and it decouples quite well and as a side benefit dampens the "swinging around". The 5 1/4'' cage in the front bottom is for the (overpriced) silentmaxx hdd silencers, since this is a noise-insulated case by that manufacturer. They do recommend adding a fan if you use them, by the way. The fan in the bottom is regulated by electronic, decoupled and nearly inaudible, too.