FS: PWM->analog Voltage Controller Circuit for pumps/fans
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
FS: PWM->analog Voltage Controller Circuit for pumps/fans
Let your BIOS or software (SpeedFan) dynamically change your pump's voltage based on your systems activity.
I have a water cooled SFF, and I was not satisfied with the noise from the water pump at idle time. My motherboard supports PWM control of all of the fans in my system, but the water pump did not support PWM, so it ran at full speed all the time.
So, I have custom designed and built a circuit that converts a PWM signal into a steady variable output voltage, specifically for water pumps, but it works with non-PWM fans too. Now I use SpeedFan to control my water pump too.
I had the circuit professionally manufactured, which meant that I had to order a few more than just one. I have a few extras that are for sale, either assembled, or as a kit.
The circuit is powered from your PSU +12V, but connects to your motherboard to report tach., and for the input PWM. The circuit will power two devices, such as a water pump and fan, but only reports the tach for one device.
The price is $35 assembled, or $20 for just the parts. S&H extra.
The voltage varries from 7.4 to ~12 volts. Most water pumps will not start reliably at a lower voltage than this.
I have a water cooled SFF, and I was not satisfied with the noise from the water pump at idle time. My motherboard supports PWM control of all of the fans in my system, but the water pump did not support PWM, so it ran at full speed all the time.
So, I have custom designed and built a circuit that converts a PWM signal into a steady variable output voltage, specifically for water pumps, but it works with non-PWM fans too. Now I use SpeedFan to control my water pump too.
I had the circuit professionally manufactured, which meant that I had to order a few more than just one. I have a few extras that are for sale, either assembled, or as a kit.
The circuit is powered from your PSU +12V, but connects to your motherboard to report tach., and for the input PWM. The circuit will power two devices, such as a water pump and fan, but only reports the tach for one device.
The price is $35 assembled, or $20 for just the parts. S&H extra.
The voltage varries from 7.4 to ~12 volts. Most water pumps will not start reliably at a lower voltage than this.
Last edited by dinofx on Thu Sep 07, 2006 6:26 am, edited 1 time in total.
Indeed, you are correct. Although, most people are shopping for a "fan controller", not thinking about the fact that the MB has sensors and control output, which can be driven often by either BIOS or SpeedFan, etc.gb115b wrote:how much would it be for you to ship 1 to the uk.
also. strictly speaking this is a pwm-> analog dc convertor (not controller)
it relies on the m/b for control right?
If I had said "converter", would you have been as likely to click on the post??
Shipping to UK is not too expensive, but the real issue is that I must physically go to the post and grab a customs form. US$43 shipped (by air).
I'm not sure I understand what you mean. My original usage was inside my Shuttle SD31P, which is an Intel chipset. A recent buyer has had success with one of the AMD chipsets.gb115b wrote:out of interest, have you tested this on any pwm supporting intel motherboards (to see if the fan can still be controlled)
Dinofx, please pm me
Dinofx I am interersted in one, maybe two of these. Please PM me.
Thanks!
Thanks!
please pm about PWM converter
Dinofx I would like to purchase one of these, SM components pre-soldered and one kit of parts. Please PM.
Thanks!
Thanks!
long time no post
but i recently purchased a G33 chipset board (MSI) which doesn't allow you to control the fan speed on 3 pin fans (no DC option), and not sure how far speedfan support will go with this board...
so i thought there may be renewed interest in this little device... did Mike ever review it?
but i recently purchased a G33 chipset board (MSI) which doesn't allow you to control the fan speed on 3 pin fans (no DC option), and not sure how far speedfan support will go with this board...
so i thought there may be renewed interest in this little device... did Mike ever review it?
Sorry, haven't visited in quite some time...
I haven't been to this site for almost a year, but I'm back. Sounds like there is a constant trickle of interested buyers. I've sold 6 of these to date (never heard a complaint), and still have 24 PCBs available. I'm short on heatsinks, but I could get the parts from futurlec in about 2 weeks, in which time I might be able to solder some of these together again.
... waiting for the drip, drip, drip of potential buyers again.
BTW, if anyone can help me out, I have a WD Raptor 150GB drive revision 00NLR0. The drive has crapped out on me, but it seems to be only a problem with the circuit board. The data isn't critical, but I'd like to get it off if someone can lend/sell/trade me a compatible Raptor.
... waiting for the drip, drip, drip of potential buyers again.
BTW, if anyone can help me out, I have a WD Raptor 150GB drive revision 00NLR0. The drive has crapped out on me, but it seems to be only a problem with the circuit board. The data isn't critical, but I'd like to get it off if someone can lend/sell/trade me a compatible Raptor.