My Biostar TF7025-M2 Review: Biostar Raises the Bar
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- Posts: 220
- Joined: Fri Jul 18, 2003 11:59 am
- Location: Vancouver, B.C.
TF7050-M2 with a picoPSU?
I saw in an earlier post that someone was planning to use this board, I assume undervolted, with a picoPSU. Can anyone report on that?
I have been recommended this MB for use in a 0 dB passive system. I am considering using it with an Athlon 64 X2 3600+, a picoPSU and a Super Talent 8 GB IDE flash drive for the main drive holding OS/mail/office/media players.
Ccould I cool the CPU passively with a Ninja or similar? Would I need a passive Northbridge chipset cooler?
Any suggestions on a good case for using with a passive cooling solution, a picoPSU and a FLASH drive? (I don't care too much about the size or shape.)
Thank you.
I have been recommended this MB for use in a 0 dB passive system. I am considering using it with an Athlon 64 X2 3600+, a picoPSU and a Super Talent 8 GB IDE flash drive for the main drive holding OS/mail/office/media players.
Ccould I cool the CPU passively with a Ninja or similar? Would I need a passive Northbridge chipset cooler?
Any suggestions on a good case for using with a passive cooling solution, a picoPSU and a FLASH drive? (I don't care too much about the size or shape.)
Thank you.
-
- Posts: 2049
- Joined: Thu Dec 15, 2005 11:06 am
- Location: Klamath Falls, OR
Basicly, the 7050 is a further, one-chip development of the 6150 and the 7025 is a further development of the 6100. The 7050-6150 is for folks who want to do lotsa TV stuff on their computer.jones_r wrote:What are the differences between the 7050 and 7025 ?, is it only that the 7050 carries an HDMI conection ?
Off the top of my head... Pure Video and HDMI.jones_r wrote:What are the differences between the 7050 and 7025 ?, is it only that the 7050 carries an HDMI conection ?
Here: http://www.nvidia.com/object/mobo_gpu_tech_specs.html
-
- Posts: 220
- Joined: Fri Jul 18, 2003 11:59 am
- Location: Vancouver, B.C.
I wasn't thinking flash for power consumption, but for noise. I currently have one of the Samsung 2.5" hard drives, that I connect via USB when I need more storage. My room is so live acoustically that it is a relief to unplug it, even though it was meant to be the quietest drive available when I got it. Off course, it is in an external aluminum enclosure.jones_r wrote:Thanks Felger.
ist.martin,
You are wasting money with the flash drive. For the same amount of money, you can get 10X the storage with a 2.5" laptop drive. Differences in power consumption will be negligible.
For 95% of my time on the computer, my current system doesn't make a peep. That is what I am trying to get to. 'Inaudible' from 2 feet away would be fine too, but I've never experienced that with fans or spinning drives. Keep in mind that I have none of the experience or skills that most people here have.
-
- Posts: 109
- Joined: Tue Sep 07, 2004 12:21 pm
- Location: USA
Re: TF7050-M2 with a picoPSU?
i'm no expert in "zero-moving-parts" systems, but i'd think it would be hard to build one around this board, unless you were using a case specifically designed for it, like Zalman TNN-300.ist.martin wrote:I have been recommended this MB for use in a 0 dB passive system.
i think when many of us use the term, "passive," we really mean the cpu or other components have a passive heatsink, but with some amount of airflow provided by case fans.
i recommended this board to ist.martin because it is said to have a very small power consumption (=heat generation). yes, in a normal ATX case with no fans, this wouldn't work, but simply laying the case on its side and leaving off the side panel, it might work (I have done this succesfully before. not pretty, but functional).i'm no expert in "zero-moving-parts" systems, but i'd think it would be hard to build one around this board, unless you were using a case specifically designed for it, like Zalman TNN-300.
An enclosed (Smart Drive 2002 or Scythe) 2.5" suspended will not be audible in a case, even if you live in a castle hall! I concur with jones_r that you will be more satisfied with a proper HD. SSD's are too expensive and not yet there performancewise.ist.martin wrote:I wasn't thinking flash for power consumption, but for noise. I currently have one of the Samsung 2.5" hard drives, that I connect via USB when I need more storage. My room is so live acoustically that it is a relief to unplug it, even though it was meant to be the quietest drive available when I got it. Off course, it is in an external aluminum enclosure.
The TNN's are nice cases but you'll get a powersupply that isn't as efficient as the Pico even if as silent. How about an Antec NSK3400, sell the PSU and replace the Tricool with a Yate or a Nexus and you'll have an inaudible cool enough running system?
Reagrds,
Kent.
Biostar' s mobos have one big drawback for HTPCs.
I was looking for them (TA690G, TF7050) but the lack of firewire is a dead end. One of the main uses of HTPC is connecting a DV camcorder on it.
Not many manufacturers gone with 7050 wich looks a nice chipset, and this is bad (November is coming the next generation NF8 chipsets with HD hardware acceleration and other big improvements and waiting 1-2 months to have 7050 takes you closed to wait one more month for next generation).
An other (better, it has firewire) option is Asrock ALiveNF7G-HDready. It undervolts from 0,8 from what i've read and has the same low power consumption.
I was looking for them (TA690G, TF7050) but the lack of firewire is a dead end. One of the main uses of HTPC is connecting a DV camcorder on it.
Not many manufacturers gone with 7050 wich looks a nice chipset, and this is bad (November is coming the next generation NF8 chipsets with HD hardware acceleration and other big improvements and waiting 1-2 months to have 7050 takes you closed to wait one more month for next generation).
An other (better, it has firewire) option is Asrock ALiveNF7G-HDready. It undervolts from 0,8 from what i've read and has the same low power consumption.
-
- *Lifetime Patron*
- Posts: 541
- Joined: Sun Jan 04, 2004 11:35 am
- Location: Chicago, Ill., USA
- Contact:
FWIW...
I just rebuilt my fiancee's computer with this motherboard and a BE-2350.
Voltages are stock (since I can't undervolt in the BIOS). Cool'n'Quiet is enabled. The machine has 2x1GB Crucial Ballistix DDR2-800 memory, and a single 120 GB Samsung PATA hard drive. Power supply is the Fortron Source "Bluestorm" 400 Watt.
At idle, under Ubuntu, the processor's voltage drops to 1.07 V, and CPU speed is 1000 GHz. Total system AC draw: 45 W.
Under load, CPU voltage jumps to 1.17 V, frequency to 2.1 GHz. Total system AC draw: 85 W.
Temps are kinda irrelevant right now, since I'm using the stock cooler (waiting on an AM2 Ninja to be delivered).
I'm guessing that this power supply is at most 60% efficient at such a light load, so real power draw by this system is much less. I've got a PicoPSU on order. Assuming 90% efficiency of the PicoPSU, idle/load AC power draw should be 30/57. That's approaching laptop-like levels! Performance is well above and beyond my fiancee's needs.
Now the only question I have is this: I read Anandtech's BE-2350 Review, where they compared BE-2350 power consumption against the Intel E4300. Intel came out lower, but of course, the major difference is chipset.
I'm wondering if the Intel G33 chipset has similar low power consumption? If so, it would be possible to build a system with still lower power.
Matt
I just rebuilt my fiancee's computer with this motherboard and a BE-2350.
Voltages are stock (since I can't undervolt in the BIOS). Cool'n'Quiet is enabled. The machine has 2x1GB Crucial Ballistix DDR2-800 memory, and a single 120 GB Samsung PATA hard drive. Power supply is the Fortron Source "Bluestorm" 400 Watt.
At idle, under Ubuntu, the processor's voltage drops to 1.07 V, and CPU speed is 1000 GHz. Total system AC draw: 45 W.
Under load, CPU voltage jumps to 1.17 V, frequency to 2.1 GHz. Total system AC draw: 85 W.
Temps are kinda irrelevant right now, since I'm using the stock cooler (waiting on an AM2 Ninja to be delivered).
I'm guessing that this power supply is at most 60% efficient at such a light load, so real power draw by this system is much less. I've got a PicoPSU on order. Assuming 90% efficiency of the PicoPSU, idle/load AC power draw should be 30/57. That's approaching laptop-like levels! Performance is well above and beyond my fiancee's needs.
Now the only question I have is this: I read Anandtech's BE-2350 Review, where they compared BE-2350 power consumption against the Intel E4300. Intel came out lower, but of course, the major difference is chipset.
I'm wondering if the Intel G33 chipset has similar low power consumption? If so, it would be possible to build a system with still lower power.
Matt
-
- Posts: 247
- Joined: Fri Oct 20, 2006 1:00 am
As far as I'm aware the AMD combination of CPU and mobo is far more efficient than Intel's.matt_garman wrote:FWIW...
I'm wondering if the Intel G33 chipset has similar low power consumption? If so, it would be possible to build a system with still lower power.
I can vouch for the low power consumption of the Asrock Alive NF7G-HDready. I just built a system with a Sempron 3200+, a Samsung 2.5" drive and dvd-rewriter, one strip of 1 GB RAM (533 mhz). The system idles at 18.8 watts, measured at the wall. That's undervolted with RMClock. At Orthos load it consumes 35W. Without RMClock the figures are 23W (C 'n Q), 27W (idle) and 47W (load).
Only problem with this board is that Quiet Fan doesn't work properly, so I can't get the CPU fan below 2500 rpm. But Asrock just sent me a test BIOS, so maybe that helps.
Oh, and Matt, I think you will see a huge improvement in the power consumption of your system after replacing that Fortron PSU. It should probably idle at around 30W.
-
- Posts: 247
- Joined: Fri Oct 20, 2006 1:00 am
-
- *Lifetime Patron*
- Posts: 541
- Joined: Sun Jan 04, 2004 11:35 am
- Location: Chicago, Ill., USA
- Contact:
I definitely expect to see an improvement with the PicoPSU over the Fortron, however, I think my initial figures were a bit too optimistic. I was guessing that the Fortron was doing about 60% at this wattage level. However, I forgot that SPCR actually reviewed the 500 W version of the PSU I have (I have the 400 W version). Based on the linked table, I'm guessing my Fortron is 70 to 75% efficient at these lower power levels.Palindroman wrote:Oh, and Matt, I think you will see a huge improvement in the power consumption of your system after replacing that Fortron PSU. It should probably idle at around 30W.
Also, too, I overestimated the PicoPSU's efficiency; when combined with the power AC-DC power brick, looks like I can expect about 85% efficiency. I don't know where I got 90%.
Anyway, an improvement is certain, but probably not as good as I originally imagined. I didn't realize the 4 pin 12 V AUX connector had to be ordered separately, so I'm waiting on that.
Matt
-
- *Lifetime Patron*
- Posts: 541
- Joined: Sun Jan 04, 2004 11:35 am
- Location: Chicago, Ill., USA
- Contact:
FYI... My fiancee's computer is all but finished (it's running on a single 1 GB RAM stick; had to RMA the 2x1 GB Ballistix because one stick was DOA).
Anyway, specs:
With the PicoPSU in place, AC power draw is 33/75 W idle/load. CPU temps are about 31/40 degrees C idle/load.
I'm quite happy!
Matt
Anyway, specs:
Code: Select all
Case Lian Li PC-A05B
PSU picoPSU-120 DC-DC + EDac 110W AC-DC brick
Motherboard Biostar Tforce TF7025-M2
CPU AMD Athlon 64 BE-2350
HSF Scythe "Ninja" SCNJ-1100 (fanless)
Fans 2x Yate Loon D12SL
Video Integrated GeForce 7025
RAM Crucial Ballistix 2x1GB DDR2-800
HD2 Samsung 160GB PATA
I'm quite happy!
Matt
Thanks to the OP for the original post which motivated me to build the following
Biostar 7025
AMD X2 4000+ with stock HSF ( set at 60% with speedfan )
2 x 1GB Ballistix 6400
WD 3.5" 160GB IDE HDD
Salvaged Dell CDRW IDE
Sonata II with 1 Tri-cool fan ( lowest setting )
Antec Earthwatts 380W PSU
Idle ( using crystalcpuid ): 1GHz/ .825V 36-37 Watts
Orthos Load: 2.1GHz/ 1.10V 66 Watts
I guess this is getting to be old news around here, but I am quite impressed with the power consumption of this combo.
I do have a question. I am only getting 3 "working" temp readings
using speedfan.
1) Temp 1 on the IT8712F chip --> CPU temp
2) A core temp, which reads way too low, but is normal i guess
3) An HD temp
Is this normal? I would expect the other two temp readings on the IT8712F chip to work and give me a case temperature and a chipset temperature.
Are mine broken?
I updated the bios using a link to the chinese website in this thread,
old bios: N68SM601
new bios N68SM702
but saw no improvement.
Thanks
Biostar 7025
AMD X2 4000+ with stock HSF ( set at 60% with speedfan )
2 x 1GB Ballistix 6400
WD 3.5" 160GB IDE HDD
Salvaged Dell CDRW IDE
Sonata II with 1 Tri-cool fan ( lowest setting )
Antec Earthwatts 380W PSU
Idle ( using crystalcpuid ): 1GHz/ .825V 36-37 Watts
Orthos Load: 2.1GHz/ 1.10V 66 Watts
I guess this is getting to be old news around here, but I am quite impressed with the power consumption of this combo.
I do have a question. I am only getting 3 "working" temp readings
using speedfan.
1) Temp 1 on the IT8712F chip --> CPU temp
2) A core temp, which reads way too low, but is normal i guess
3) An HD temp
Is this normal? I would expect the other two temp readings on the IT8712F chip to work and give me a case temperature and a chipset temperature.
Are mine broken?
I updated the bios using a link to the chinese website in this thread,
old bios: N68SM601
new bios N68SM702
but saw no improvement.
Thanks
-
- Posts: 1
- Joined: Wed Aug 29, 2007 8:05 pm
-
- *Lifetime Patron*
- Posts: 541
- Joined: Sun Jan 04, 2004 11:35 am
- Location: Chicago, Ill., USA
- Contact:
I did have to buy a four pin 12 V AUX cable. It's basically an adapter cable that converts a four-pin molex connector to the four pin P4 12 V AUX. In other words, one of these.judd.tracy wrote:Did it take anything special to get the PicoPSU working with the TF7025-M2? Did you have to add a four pin cable to attach to the processor power plug?
I was under the impression that this adapter came with the PicoPSU, but it does not.
Note also that the PicoPSU is for a 20-pin ATX header, and the TF7025-M2 (like most newer motherboards) has a 24-pin ATX header. You can buy a 20 to 24 pin adapter, but it's not necessary. Just plug the 20-pin PicoPSU straight into the 24 pin ATX port on the motherboard and you'll be fine. (That's how I'm running mine.)
Matt
Edit: note you'll also have to buy a 4-pin molex to SATA adapter cable if you have SATA drives.
-
- Posts: 109
- Joined: Tue Sep 07, 2004 12:21 pm
- Location: USA
i just posted it here. (in response to you, i think ).HReality wrote:Just for curiosity is anybody runninglinux and do they have an xorg they could post with both the DVI-I and VGA ports listed?
actually, i'm only using the DVI, haven't used the VGA port.
Does this board support dual monitor?
Does the Onboard Video Options support dual monitor option?
or do I have to purchase a new PCIe Graphic to set up a Dual Monitor Setting?
Please help, I need to know A.S.A.P
I need advice on which Graphic Card or Video Card will work with this board...
Thanks
Han
or do I have to purchase a new PCIe Graphic to set up a Dual Monitor Setting?
Please help, I need to know A.S.A.P
I need advice on which Graphic Card or Video Card will work with this board...
Thanks
Han
thanks guys for clear this out
Thanks for this quick repose of the Dual Monitor Option...
So, what are my options here?
Dump My Old Monitor Get a new Flat Panel (Digital Input)...
Or Get a Graphic Card add-in????
Which one is a better option?
Which one is cheap... to resolve this problem?
Any idea, which monitor should I get?
Or
Which reliable video card will work best with this MB?
Looks like I am gonna have to go over my budget now..
Thanks
Han
So, what are my options here?
Dump My Old Monitor Get a new Flat Panel (Digital Input)...
Or Get a Graphic Card add-in????
Which one is a better option?
Which one is cheap... to resolve this problem?
Any idea, which monitor should I get?
Or
Which reliable video card will work best with this MB?
Looks like I am gonna have to go over my budget now..
Thanks
Han
-
- Friend of SPCR
- Posts: 118
- Joined: Wed Jul 04, 2007 3:29 pm
- Location: Lost and Found Bin, Cypress, CA, USA
- Contact:
Sorry it has taken me so long to reply, but here goes... In Speedfan, the "Temp1" on the IT8712F chip does indeed agree with the CPU temperature in the BIOS as well as the CPU temperature in the Biostar monitoring software. It also has a K8 Core temperature, as well as the HDD and an ACPI temperature. Everest displays the DTS temperature as "AUX", as well as two core temperatures (Core #1 and Core#2). Core #2's absurdly low number agrees with Core in Speedfan. The aforementioned DTS temperature has always read the same across all 4 sources, but before the BIOS upgrade (to the N68SM702 on the Chinese site), they were regularly quite high for my setup. Current temperature readings are as follows:wwcameron wrote: I do have a question. I am only getting 3 "working" temp readings
using speedfan.
1) Temp 1 on the IT8712F chip --> CPU temp
2) A core temp, which reads way too low, but is normal i guess
3) An HD temp
Is this normal? I would expect the other two temp readings on the IT8712F chip to work and give me a case temperature and a chipset temperature.
Are mine broken?
I updated the bios using a link to the chinese website in this thread,
old bios: N68SM601
new bios N68SM702
but saw no improvement.
Thanks
Ambient air temperature (according to the thermostat reading in this room as well as another thermometer): 23-24°C
DTS: 27°C (Prior to the BIOS update, this was around 40 with exactly the same setup)
Core#1: -4°C (I don't remember installing refrigeration equipment in this computer!)
Core#2: 4°C, momentarily bouncing up to a sweltering 9°C at seemingly random intervals
HDD: 34°C (It's always been a warm running drive)
ACPI: 34°C (Judging by the barely warmed air coming out the back of the case, this has to be the chipset temp and not the case temp)
Hope this helps!
EDIT: Just added my setup in my signature, and I'd like to add my power consumption results measured with my Kill-A-Watt meter that I just got back. I use CrystalCPUID for dynamic over/underclocking of my Brisbane 3600+ with the following P-states: 0.850V @ 4.5x 1138 MHz, 1.000V @ 7.0x 1771 MHz, and 1.175V @ 9.5x 2403 MHz.
Idle, 1138 MHz: 43W
Load 1, 2.4 GHz: 83W
Load 2, 2.4 GHz: 87W
Load 1 is simply 2x CPUBurn, Load 2 is running Everest's integrated System Stability Test, in which all the options are enabled: Stress CPU, Stress FPU, Stress Cache, Stress System Memory, Stress Local Disks.
On another note entirely, if I had it all to do over again, I would spend the extra $10 or so for the 7050. The H.264 hardware acceleration alone is well worth the extra cost, not to mention the option for HDMI connectivity (it includes an HDMI-to-DVI adapter IIRC).
What were the symptoms of the SATA timeout problem? Which ports were bad? In which mode were you using the sata ports ( AHCI, RAID, or IDE ) ?vg30et wrote:
I just sent my TF7050 board back to newegg for a replacement. I had a SATA timeout issue that was getting progressively worse and Biostar determined the issue was with 2 bad SATA ports. I've seen some reports of reliability issues on newegg reviews too.
My 7025 has some issues with long boot times, and not waking up from suspend after I moved the OS to a SATA drive. Trying to diagnose. Thanks
TF7050 and SpeedFan
Does SpeedFan work correctly with the TF7050? I cannot get it to display CPU temperature correctly. More importantly, I cannot get it to control fan speed. The fan speed option disappeared from BIOS after I installed SpeedFan!
Help. My new build is very LOUD!
BTW, I am running 32-bit Vista on Brisbane 4000+.
Help. My new build is very LOUD!
BTW, I am running 32-bit Vista on Brisbane 4000+.