120mm Evercool Aluminium Fan
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
120mm Evercool Aluminium Fan
http://www.pccasegear.com/prod564.htm
how does it look?
seems like it would be pretty quiet undervolted with good airflow.
Cheaper than the Panaflo 120mm fans here
how does it look?
seems like it would be pretty quiet undervolted with good airflow.
Cheaper than the Panaflo 120mm fans here
I have the mediumspeed fan of the series (2000RPM, 79.14CFM, 29db) as my only fan (onefan-system) and it works like a charm undervolted to 5V. When at 5V it reports about 1100RPM and is only audible while I sit right next to the puter at the floor. When I sit infront of my screen (3-4 feet in front if and about 1 feet above) the fan I can not hear it. The sound it does emanate is lowpitched and is so far liveable.
With the fanmate at full throttle, the story is a bit different, though. At 11V (max with fanmate) it has a very clear voshing sound, which I guess is as it should, since it moves an incredible amount of air. I have reversed airflow in my case with the fan mounted at the rear exhaust reversed and when I turn the fan up to max I can clearly feel a steady breese in front of my case exceeding any airflow I have felt from any PSU.
When comparing db/CFM this fan is better than any fan MikeC has posted in his list of fans and their airflow and soundlevel according to manufactorer, with a ratio of 0,366.
http://www.silentpcreview.com/modules.p ... =25&page=1
Undervolted you can´t go wrong with this fan. I have experienced no clicking noices, it has no problems starting undervolted, it has low noice and it moves alot of air.
With the fanmate at full throttle, the story is a bit different, though. At 11V (max with fanmate) it has a very clear voshing sound, which I guess is as it should, since it moves an incredible amount of air. I have reversed airflow in my case with the fan mounted at the rear exhaust reversed and when I turn the fan up to max I can clearly feel a steady breese in front of my case exceeding any airflow I have felt from any PSU.
When comparing db/CFM this fan is better than any fan MikeC has posted in his list of fans and their airflow and soundlevel according to manufactorer, with a ratio of 0,366.
http://www.silentpcreview.com/modules.p ... =25&page=1
Undervolted you can´t go wrong with this fan. I have experienced no clicking noices, it has no problems starting undervolted, it has low noice and it moves alot of air.
Well I have the fan, among other goodies. fast service, everything was packed well. Will be doing mroe business with them in the future
But the specs on the back of the fan package is different from the website. Its the same fan as yours by the look of things
Speed - M
RPM - 2000
Voltage - 12
Current - 0.38
Air Flow - 79.14
Air Pressure - 2.83
Noise - <30
not a biggy even better
I can't test it yet, waiting on my case/psu etc. But it will be like yours I'm sure.
It's quite heavy, the aluminium frame could act like a heatsink, but it will most likely be decoupled anyway.
Comes with a 3 pin header.
But the specs on the back of the fan package is different from the website. Its the same fan as yours by the look of things
Speed - M
RPM - 2000
Voltage - 12
Current - 0.38
Air Flow - 79.14
Air Pressure - 2.83
Noise - <30
not a biggy even better
I can't test it yet, waiting on my case/psu etc. But it will be like yours I'm sure.
It's quite heavy, the aluminium frame could act like a heatsink, but it will most likely be decoupled anyway.
Comes with a 3 pin header.
WOW !
I just ran the fan off the Molex to just listen to it at 12V and its very quiet as is! It has a very smooth woosshing air sound, but that's about it.
Great fan!
In contrast the 80mm Panalo M I have has a rather loud hum at 12v!
even though it's rated at around the same Db.....
If anyone wants a quality quiet 120mm fan look no further
I just ran the fan off the Molex to just listen to it at 12V and its very quiet as is! It has a very smooth woosshing air sound, but that's about it.
Great fan!
In contrast the 80mm Panalo M I have has a rather loud hum at 12v!
even though it's rated at around the same Db.....
If anyone wants a quality quiet 120mm fan look no further
That is good to know, thanks! I will probably try one soon too.CoolColJ wrote:WOW !
I just ran the fan off the Molex to just listen to it at 12V and its very quiet as is! It has a very smooth woosshing air sound, but that's about it.
Great fan!
In contrast the 80mm Panalo M I have has a rather loud hum at 12v!
even though it's rated at around the same Db.....
If anyone wants a quality quiet 120mm fan look no further
I have a Sonata and the 120mm case fan even when run off the fan output has a low freq resonance. But when I replaced it with the 120mm Evercool run at 5v, wow the drop in noise is pretty dramatic. The only major nosie maker is the Antec PSU, but even that is very low in noise from where I sit, during the day. Seasonic super silencer will fix that. The ZM80 (on radeon 9800 - cools it well even when heavily overclocked!) and 7000alcu at 5v thanks to the Zalman fan controller can't be heard
The P4 2.8c I have is overcloked to 3.5 gigahertz too and ildes under 40 degrees
That 120mm fan makes a big diffference as far as airflow goes.
Only thing is that I can't use the Silicon fan grommets from the Sonata with it, but if you use a 120mm silicon fan mount then it's no problem. But I mounted mine against bare metal and I can't hear any vibration - 5volts ensures that I guess
But then again the Antec fan run at 5volts might be just as quiet
The P4 2.8c I have is overcloked to 3.5 gigahertz too and ildes under 40 degrees
That 120mm fan makes a big diffference as far as airflow goes.
Only thing is that I can't use the Silicon fan grommets from the Sonata with it, but if you use a 120mm silicon fan mount then it's no problem. But I mounted mine against bare metal and I can't hear any vibration - 5volts ensures that I guess
But then again the Antec fan run at 5volts might be just as quiet
this fan can run at very low speeds just fine! 700-800RPM (3volts?)and is damn quiet at this speed!
see this thread
http://forums.silentpcreview.com/viewto ... 7033#47033
see this thread
http://forums.silentpcreview.com/viewto ... 7033#47033
Well I finally have a 4 pin to 3 pin cable so I can finally control my Antec Sonata stock 120mm fan with my Zalman Fan controller.
With the Evercool and Antec fan at 5volts. the Evercool is louder, mostly air rushing turbelence sounds - air rushing roar. But when I put both against my face, the Evercool is sure pushing a ton more air.
The hum levels seems about the same, but the roar makes the Evercool a few DBs louder. The Antec fan has this faint "ticking or rattling sound" very faint though, sorta like a chatter, but you can't hear it unless your ear is right up against it or standing directly behind the case.
The Evercool can run at lower volts than 5, if I double up a Fanmate as mentioned above, and then runs a lot quieter, but it always has more air turblence, and at 3 volts or so doesn't move much air.
The CPU temp does rise 2-3 degrees when I do so. At 4 volts it still moves a lot of air, but not bad noise wise, around 1000 RPM.
So I'm not so sure if it's as good for someone who want's real quietness. But if you want a fairly quiet fan at low voltage that still moves a lot of air then it's a good one.
I certainly can barely hear it from where I sit, well my whole system in general
With the Evercool and Antec fan at 5volts. the Evercool is louder, mostly air rushing turbelence sounds - air rushing roar. But when I put both against my face, the Evercool is sure pushing a ton more air.
The hum levels seems about the same, but the roar makes the Evercool a few DBs louder. The Antec fan has this faint "ticking or rattling sound" very faint though, sorta like a chatter, but you can't hear it unless your ear is right up against it or standing directly behind the case.
The Evercool can run at lower volts than 5, if I double up a Fanmate as mentioned above, and then runs a lot quieter, but it always has more air turblence, and at 3 volts or so doesn't move much air.
The CPU temp does rise 2-3 degrees when I do so. At 4 volts it still moves a lot of air, but not bad noise wise, around 1000 RPM.
So I'm not so sure if it's as good for someone who want's real quietness. But if you want a fairly quiet fan at low voltage that still moves a lot of air then it's a good one.
I certainly can barely hear it from where I sit, well my whole system in general
Well I put back the Evercool into my case.
This is what I found, the SOnata 120mm fan can be heard even at 5volts. Not so much air noise, but a sorta muted drone.
It will always spin up even at under 5volts - at least mine does
The Evercool has more turblence noise, but it also moves more air and has no drone. But the Evercool at 900RPM (less than 5 volts which is 1150RPM) moves more air than the Sonata fan at 5volts and can't be heard from my sitting position. Also the exhaust air is much cooler for some reason.
I suspect the mass of the alumium frame does help in this regard.
This is what I found, the SOnata 120mm fan can be heard even at 5volts. Not so much air noise, but a sorta muted drone.
It will always spin up even at under 5volts - at least mine does
The Evercool has more turblence noise, but it also moves more air and has no drone. But the Evercool at 900RPM (less than 5 volts which is 1150RPM) moves more air than the Sonata fan at 5volts and can't be heard from my sitting position. Also the exhaust air is much cooler for some reason.
I suspect the mass of the alumium frame does help in this regard.
-
- Patron of SPCR
- Posts: 946
- Joined: Sat Sep 06, 2003 9:57 pm
- Location: Berkeley, CA, USA
- Contact:
Hmm, well, just got my Evercool aluminum 120mm. Initial reaction is positive-- minus the whooshing sound of air, the fan itself doesn't generate much noise at all. Seems to be on par or a bit better than the Enermax 120mm, which is quite good, but I'll need more time to play with it.
Man, is this thing heavy! Unfortunately the weight precludes mounting on the Zalman bracket, which was the original plan.
I also got a Zalman fanmate, finally, so I have a finer level of voltage/rpm control.
Man, is this thing heavy! Unfortunately the weight precludes mounting on the Zalman bracket, which was the original plan.
I also got a Zalman fanmate, finally, so I have a finer level of voltage/rpm control.
Fanmate only goes down to 5volts though I think
I have both a Fanmate (from my 7000Alcu) and a Zalman Fan controller inline, so I can get below 5 volts
I set the Fanmate just a bit above where the Evercool won't spin up and then adjust to taste with the Zalman Fancontroller.
Off course a SunBeam Fancontroller can go lower than 5volts.
I have both a Fanmate (from my 7000Alcu) and a Zalman Fan controller inline, so I can get below 5 volts
I set the Fanmate just a bit above where the Evercool won't spin up and then adjust to taste with the Zalman Fancontroller.
Off course a SunBeam Fancontroller can go lower than 5volts.
Well I am glad in hindsight I opted for the Evercool. The Panaflo 120mm is both more expensive and lacks RPM monitoring.
Initally I bought it, because I thought I'd have it exhausting the air from the Sonata, and the Sonata 120mm fan sucking. But I don't really need two fans in my system. The Evercool moves more than enough air for my needs at low voltage.
Initally I bought it, because I thought I'd have it exhausting the air from the Sonata, and the Sonata 120mm fan sucking. But I don't really need two fans in my system. The Evercool moves more than enough air for my needs at low voltage.
-
- Patron of SPCR
- Posts: 946
- Joined: Sat Sep 06, 2003 9:57 pm
- Location: Berkeley, CA, USA
- Contact:
This is a great little fan. After more extended use, I can rate it as the quietest 120mm fan, PER AIR VOLUME, I've owned-- slightly beating out the Enermax 120mm and clobbering everything else (vantec, sunon, etc). There is no discernable electric or mechanical noise, it's all air movement.
Panaflo 120mm x 38mm might be as quiet but moves a lot less air.
Panaflo 120mm x 38mm might be as quiet but moves a lot less air.
-
- *Lifetime Patron*
- Posts: 5316
- Joined: Sat Jan 18, 2003 2:19 pm
- Location: St Louis (county) Missouri USA
Stuffed into this oak case, my Evercool 120mm is doing most of cooling. It draws air from the top of the case, pulls it over the board and cpu, around the hard drives, down into the wood case, and blows it out through the PSU which has it's own fan removed.
All this at about 1200 rpm, which is as low as the controller will go. Great fan.
All this at about 1200 rpm, which is as low as the controller will go. Great fan.
that's one interesting PeeCeeBluefront wrote:Stuffed into this oak case, my Evercool 120mm is doing most of cooling. It draws air from the top of the case, pulls it over the board and cpu, around the hard drives, down into the wood case, and blows it out through the PSU which has it's own fan removed.
All this at about 1200 rpm, which is as low as the controller will go. Great fan.
I was at CompUSA yesterday to get a new mainboard battery, and I happened to take a look at their fan section. To my surprise, they actually had the Evercool 120mm Aluminum in a CompUSA badged box selling for $17.XX. It's definitely the Evercool (it has the logo on the fan), and they also have it's smaller siblings. I may have to pick one up next time!
Thought you'd like to know.
Emmett Lyman
Thought you'd like to know.
Emmett Lyman
Well now I've gotta make a trip to the hardware store to get the right size screws because i want to use some siliceous sheeting in between the fan and case and the 6mm screws just don't seem to cut it. Even without that bit in between, the screws don't really grip... and i don't want the fan flapping about in my case whenever i crank it.
(sigh) Ahhh nuts.
Still, what a peculiar way of fan mounting they came up with.
(sigh) Ahhh nuts.
Still, what a peculiar way of fan mounting they came up with.
how do those silicon sheets work? do they just sit between the fan and the case?
because wouldn't the fans still transmit vibration through the screws and on to the case anyway?
i understand how the e.a.r isolators work, they fully separate the case from the fan with rubber, but by the sound of it, these sheet thingos aren't?
because wouldn't the fans still transmit vibration through the screws and on to the case anyway?
i understand how the e.a.r isolators work, they fully separate the case from the fan with rubber, but by the sound of it, these sheet thingos aren't?